manualshive.com logo in svg

Fujitsu Siemens Computers PRIMERGY RX100 S4, User Manual

Share
Download
Fujitsu Siemens Computers PRIMERGY RX100 S4 User Manual Download Page 47

47

PRIMERGY RX100 S4 User’s Guide    

2

Checkin

g before O

S

 Inst

allatio

n

License for Use of System for ServerStart

"License for Use of System for ServerStart" linked from the ServerStart startup window is a license for 

use of Windows PE contained in the ServerStart CD-ROM. Windows PE for starting up ServerStart can 

be only used for installing Windows Server 2003 or Windows 2000 Server provided under a separate 

legal license.

Setting Up the Printer

ServerStart does not support setup of printers. Perform installation after setup is completed.

2.3.5 Expansion Cards Supported by ServerStart

ServerStart supports automatic driver installation for the following expansion cards.

2.3.6 Cautions for Manual Installation

Notes on Using an Array Controller

Before the OS is installed, the array controller must be configured and the system drive under the array 

controller must be initialized. For more details, refer to the manual in the Array Controller Document & 

Tool CD.

Installing Windows 2000 Server

To install Windows 2000 Server manually, use the OS CD-ROM with Service Pack 4 applied. Apply the 

following hotfix module stored in ServerStart Disk 1 CD-ROM after installation.

 

[CD-ROM drive]: \HOTFIX\W2K\

Free Space Required for Installation

The partition where the OS is installed must have enough free space for obtaining memory dump. For 

more details, refer to "5.1 Memory Dump/Paging File Setting" (

pg.134).

table: Automatic Expansion Card Driver Installation

Name

Model

Bus

Onboard FDD/IDE

-

-

Onboard LAN

-

PCI-E

Onboard VGA

-

PCI

LAN card

PG-1862

PCI-X

PG-1882L

PCI-X

PG-1892L

PCI-X

PG-2861L

PCI-E

PG-289L

PCI-E

SCSI card

PG-1301L

PCI

Summary of Contents for PRIMERGY RX100 S4






























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands