FUJIPLA AL-MEISTER ALM3230 Instruction Manual Download

Page: 60 / 68

DryLam

A Trademark of Martin Yale Industries

251 Wedcor Avenue, Wabash, IN 46992

Brian Jennett- Tech-Line & Service Advisor/Manager

Phone: (260-569-7231)

www.DryLam.com

ALM3230 Customer Instruction Manual.docx

Page 60 of 68

5. AUTOMATIC OPERATION (cont’d)

5-5. ECO MODE (Power Saving Mode)

ECO MODE enters when the machine is idle and any

buttons on the operation panel* have not been

pressed in the past 15 minutes.

*This does not apply to the “MOVE” switch.

A buzzer will sound 1 minute before entering ECO MODE. ECO MODE will be deactivated by pressing any

button, the 15 minute timer then starts again.

1) Current temperature.

2) ECO MODE temperature goal (140F).

5-6. TERMINATE LAMINATION

1. Make sure the lamination has finished.

2. Turn off Power Switch.

3. Disconnect the power plug.

Summary of Contents for AL-MEISTER ALM3230





































































Search results

Summary of Contents for AL-MEISTER ALM3230

Reviews:

Related manuals for AL-MEISTER ALM3230

Brands by name

Popular brands

FUJIPLA AL-MEISTER ALM3230, Instruction Manual

Search results

Summary of Contents for AL-MEISTER ALM3230

Reviews:

Related manuals for AL-MEISTER ALM3230

Brands by name

Popular brands