manualshive.com logo in svg

Fuji Xerox DocuPrint CM225FW, User Manual, Page: 61 / 344

Share
Download
Fuji Xerox DocuPrint CM225FW User Manual Download Page 61

Printer Connection and Software Installation

61

Using Installer to Set Up Connection and Install Software

NOTE: 

•

The following procedure sets up printer connection and then install the drivers and software. If you have already established 
printer connection, see "Using Installer to Install Software" on page 64 to install the print driver and software immediately.

Launching the FX Printer Installation Screen

1

Insert the 

Software Pack CD-ROM

 into your computer to start the 

FX Printer Installation

 screen.

NOTE: 

•

For Windows 8, Windows 8.1, Windows Server

®

 2012, and Windows Server 2012 R2, click the message displayed on 

the upper right corner of the screen, and then select 

Run setup.exe

.

•

If the CD does not automatically launch, perform the following steps.

a

For Windows Server 2003, Windows Server 2008, and Windows Server 2008 R2, click Start 

 Run.

For Windows Vista

®

 and Windows 7, click 

Start

 

 

All Programs

 

 

Accessories

 

 

Run

.

For Windows 8 and Windows Server 2012, right-click on the 

Start

 screen and click 

All apps

 

 

Run

.

For Windows 8.1 and Windows Server 2012 R2, click 

 on the 

Start

 screen 

 

Run

.

b

Enter "D:\setup.exe" (in case your optical disk drive is D), and then click 

OK

.

2

Click 

Setup Printer and Install Software

.

3

If you agree to the terms of the 

License Agreement

, choose 

I accept the terms of the license agreement

, 

and then click 

Next

.

Summary of Contents for DocuPrint CM225FW

























































































































































































































































































































































Reviews:

No comments