manualshive.com logo in svg

Fuji Xerox DocuPrint CM225FW, User Manual

The Fuji Xerox DocuPrint CM225FW is a versatile all-in-one printer designed for small businesses. With its user-friendly interface and advanced features, it offers an efficient printing experience. To ensure seamless operation, users can easily access the free User Manual for this product on our website, manualshive.com, where they can conveniently download it.

Share
Download
background image

Using the Operator Panel Menus and Keypad

221

Fax Number

Purpose:
To set the fax number of the printer, which will be printed on the header of a fax message.

NOTE: 

•

Make sure to specify 

Fax Number

 before using 

Junk Fax Filter

.

Region

Purpose:
To select the region where the printer is used. The change becomes effective after the printer is turned off and then 
on.
Values:

Company Name

Purpose:
To set the sender name to be printed on the header on faxes.

Line Type

Purpose:
To select the default line type. The change becomes effective after the printer is turned off and then on.
Values:

Line Monitor

Purpose:
To set the volume of the line monitor, which audibly monitors a transmission through the internal speaker until a 
connection is made.
Values:

Unknown

*

Australia
Cambodia
China 
Hong Kong
Indonesia
Laos
Malaysia
Myanmar
New Zealand
Philippines
Singapore
South Korea
Taiwan
Thailand
Vietnam

PSTN

*

Uses PSTN.

PBX

Uses PBX.

Off

Turns off the volume of the line monitor.

Min

Sets the volume of the line monitor to minimum.

Middle

*

Sets the volume of the line monitor to middle.

Max

Sets the volume of the line monitor to maximum.

Summary of Contents for DocuPrint CM225FW

























































































































































































































































































































































Reviews:

No comments

Related manuals for DocuPrint CM225FW

DataCard CR500 Quick Install Manual preview
CR500
Brand: DataCard Pages: 17
DataCard CR500 User Reference Manual preview
CR500
Brand: DataCard Pages: 24
Oki T400 Guía De Instalación preview
T400
Brand: Oki Pages: 36
Oki T400 Installation preview
T400
Brand: Oki Pages: 3
Oki C3300n Specifications preview
C3300n
Brand: Oki Pages: 1
Canon imageRUNNER 5075 Reference Manual preview
imageRUNNER 5075
Brand: Canon Pages: 502
Cannon imageRUNNER 5075 Support Manual preview
imageRUNNER 5075
Brand: Cannon Pages: 268
Xerox 4150S - WorkCentre B/W Laser Brochure & Specs preview
4150S - WorkCentre B/W Laser
Brand: Xerox Pages: 4
Xerox WorkCentre 7655 Evaluator Manual preview
WorkCentre 7655
Brand: Xerox Pages: 24
Ricoh AC122 User Manual preview
AC122
Brand: Ricoh Pages: 278
Xerox VersaLink C400V User Manual preview
VersaLink C400V
Brand: Xerox Pages: 196
Xerox WorkCentre M118i Quick Setup Manual preview
WorkCentre M118i
Brand: Xerox Pages: 5
Konica Minolta Bizhub 4050i Shortcut Manual preview
Bizhub 4050i
Brand: Konica Minolta Pages: 44
A&D TM-2480 Instruction Manual preview
TM-2480
Brand: A&D Pages: 66
Ricoh SP C222DN Administration Manual preview
SP C222DN
Brand: Ricoh Pages: 284
Epson T545500 Material Safety Data Sheet preview
T545500
Brand: Epson Pages: 4
Epson T549300 Material Safety Data Sheet preview
T549300
Brand: Epson Pages: 4
Epson T545600 Material Safety Data Sheet preview
T545600
Brand: Epson Pages: 4

Brands by name

Popular brands

Load more brands