manualshive.com logo in svg

Fuji Xerox DocuPrint C3055 DX, User Manual

Share
Download
Fuji Xerox DocuPrint C3055 DX User Manual Download Page 166

166

7 Maintenance

Replacing the Drum Cartridge

The following messages appear on the display when the drum cartridge is near the end of 
its life.

WARNING

• Never throw a drum cartridge into an open flame. Toner remaining in the cartridge can 

cause an explosion and you can get burnt.

Important

• Make sure that the power is switched on when replacing the drum cartridge. Switching the power off 

erases the print data in the printer and information accumulated in the memory.

• Do not expose the drum cartridge to direct sunlight or strong light.
• Avoid exposure to strong light when installing the drum cartridge and complete the installation in less 

than one minute.

• Do not touch the surface of the intermediate transfer belt (black portion on the bottom) or the 

photosensitive drum (blue portion on the back side). Do not place the drum cartridge upright or upside 
down. Doing so can damage the drum.

• Place the drum cartridge only on a flat surface.

Replacement Procedure

Follow these steps to replace the drum cartridge and to clean inside the printer.

1.

If paper is loaded in the bypass tray, 
remove the paper and close the bypass 
tray cover.

Important

• When closing the bypass tray cover, be careful not to 

get your fingers caught between (the left or right edge 
of) the cover and the printer.

Message

Action

Ready to print
Drum Cartridge
Replace soon

The cartridge does not need to be replaced right away, 
but have a new cartridge ready.

Replace Drums
Cartridge

The printer stops and becomes unable to print. 
Replace the drum cartridge.

Place the side with the handles facing up.

Summary of Contents for DocuPrint C3055 DX















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands