manualshive.com logo in svg

Fuji Xerox DocuPrint C3055 DX, User Manual

Share
Download
Fuji Xerox DocuPrint C3055 DX User Manual Download Page 164

164

7 Maintenance

Replacing a Toner Cartridge

Use the following procedure when replacing a toner cartridge.

Note

• If the toner cartridge that needs to be replaced is not at the top of the cartridge slot, rotate the cartridge 

slot using the control panel. For more information, refer to "Rotating a Toner Cartridge" (P. 163).
If the "Replace Toner" message is displayed and the printer is not in operation, the cartridge indicated in 
the message is placed usually at the top on the cartridge slot. 

1.

Place your fingers into the inset grip on the 
left side of the top cover, and lift the cover 
open.

2.

Rotate the lever on the right side of the 
toner cartridge to the front, and align the 

mark on the cartridge with the   

mark on the printer.

3.

Lift the toner cartridge and remove it from 
the printer.

Important

• Do not touch the interior of the printer. Some parts 

may be hot.

4.

Have ready the cartridge of the color 
indicated in the message.
The color of the cartridge is indicated also 
on the cartridge slot.

same color

Summary of Contents for DocuPrint C3055 DX















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands