Fuji Xerox DocuPrint C2120 User Manual Download | Manualshive

Page: 89 / 206

background image

5.2 Description of Menu Items

89

Protocol

Select [Enable] when using the protocol. When [Disable] is selected, the
protocol cannot be activated.
• [LPD] (default: [Enable])
• [Port9100] (default: [Enable])
• [IPP] (default: [Enable])
• [SMB (TCP/IP)] (default: [Enable])
• [SMB (NetBEUI)] (default: [Enable])
• [FTP] (default: [Enable])
• [WSD] (default: [Enable])
• [E-mail Printing] (default: [Enable])
• [SNMP]-[SNMP (UDP/IP)] (default: [Enable])
• [StatusMessenger] (default: [Enable])
• [InternetServices] (default: [Enable])
• [Bonjour (mDNS)] (default: [Enable])
• [Telnet] (default: [Enable])
• [HTTP - SSL/TLS] (default: [Enable])

Note

• [HTTP - SSL/TLS] appears only when a certificate is registered on the

printer.
For details on encrypting HTTP communication and a certificate required
for the printer, refer to "SSL Data Encryption for HTTP Communication" (P.
149).

• [HTTP - SSL/TLS] does not appear on the model sold in China.

IP Filter

Specifies blocking the reception of data from certain IP addresses.

No. n
(n:1 to 5)

You can set up to five IP addresses ([No. 1] to [No. 5]). [No. 1] has priority
over the others. To set multiple filters, set IP address in descending order from
the address network with the narrowest range.
• [Address]

Enter the IP addresses using numbers between 1 and 255. The first xxx,
however, cannot be 127 or a number between 224 and 255.

• [Mask]

Enter the subnet masks using the following numbers:
0, 128, 192, 224, 240, 248, 252, 254, and 255.

• [Mode]

Sets the restriction conditions for the addresses from [Off] (default),
[Accept], or [Reject].

Note

• [IP filter] can be set also on CentreWare Internet Services. For details, refer

to
"Controlling Data Reception by IP Address" (P. 153).

IEEE 802.1x

Disables the IEEE 802.1x feature.

Note

• [IEEE 802.1x] appears only when the feature is enabled.
• [IEEE 802.1x] appears when using the wired network only.
• [IEEE 802.1x] does not appear on the model sold in China.

Initialize NVM

Initializes network data stored in NVM. The NV memory is nonvolatile memory
that retains the settings of the printer even when its power is switched off.
Initializing the NV memory will return each item of the [Wired Network] menu
to its default value.

Item

Description

«
...
87
88
89
90
91
...
»

Summary of Contents for DocuPrint C2120















































































































































































































Reviews:

No comments

Related manuals for DocuPrint C2120

Brand: LabelTac Pages: 2

Brand: Oki Pages: 147

Brand: Oki Pages: 12

Brand: Oki Pages: 297

Brand: Oki Pages: 111

Brand: Oki Pages: 6

Brand: Oki Pages: 2

Brand: Oki Pages: 108

C5800Ldn Series

Brand: Oki Pages: 266

C5800Ldn Series

Brand: Oki Pages: 276

Brand: Oki Pages: 121

Brand: Oki Pages: 12

Brand: Oki Pages: 354

Brand: Oki Pages: 78

Brand: Oki Pages: 328

Brand: Oki Pages: 24

Brand: Oki Pages: 719

Brand: Oki Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands