Fuji Xerox DocuPrint C2120 User Manual Download

Page: 54 / 206

3 Print

Operations on the Control Panel

Follow the procedure described below to print a Secure Print job stored from the printer.

Note

• When deleting a Secure Print job without printing, select [Delete] after Step 8 in the following procedure.

Press the < > button on the control panel.

Press the < > or <Eject/Set> button to
accept the selection.
A user ID is displayed.

Press the < > button until the desired user
ID is displayed.

Note

• The user ID is the ID set under [User ID] in the [Secure

Print] dialog box of your print driver.

Press the < > or <Eject/Set> button to
accept the selection.
A screen that allows you to enter a
password is displayed.

Enter your password using the < > and
< > buttons. Use the < > button to move
the cursor.

Note

• Enter the password set under [Secure Print Passcode]

in the [Secure Print] dialog box of your print driver.

Press the <Eject/Set> button to confirm
your setting.
The name of a document stored in the
printer is displayed.

Press the < > button until the desired
document name is displayed.

Note

• The document name is the name (of up to 12 bytes)

set under [Document Name] in the [Secure Print]
dialog box on your print driver.

• When more than one document is stored in the printer,

you can also select [All Documents].

Print Menu

Secure Print

Select User ID

User1

PSET key

[_ ]

PSET key

[**** ]

Select Document
Report1

Summary of Contents for DocuPrint C2120














































































































































































































Search results

Summary of Contents for DocuPrint C2120

Reviews:

Related manuals for DocuPrint C2120

Brands by name

Popular brands

Fuji Xerox DocuPrint C2120, User Manual

Search results

Summary of Contents for DocuPrint C2120

Reviews:

Related manuals for DocuPrint C2120

Brands by name

Popular brands