Fuji Xerox DocuPrint C1110 B Page 175 User Manual Download | Manualshive

Page: 175 / 209

background image

7.17 Moving the Printer

175

7.17

Moving the Printer

Important

• This product (including the consumables) weighs 17.0 kg. When moving it, always carry it by a team of

two or more persons to avoid mishandling or injury.

• When lifting this product, firmly grip the recessed areas provided on both sides of the machine. Never lift

it by gripping any other areas. It will avoid you from dropping the product and getting back ache or
injuries.

Use the following procedure when moving the printer.

1.

Switch the power off by pressing the power switch located on the left side of the
printer to the <O> position.

2.

Unplug the power cord, interface cable, and all the other cables from the printer.

3.

Open the side cover.

4.

Remove all toner cartridges from the printer.

Important

• Make sure to remove the toner cartridges before moving the printer. Otherwise, the toner may spill in the

printer.

• Do not shake the toner cartridges after removing them. The toner may spill.
• Be careful not to get your hands or clothes dirty with toner. If toner gets on your hands or clothes, wash

it off immediately.

Note

• For information on how to remove the toner cartridges, refer to "Replacing the Toner Cartridges" (P.

5.

Close the side cover.

6.

Push the side button (right side) and open the front cover.

7.

Hold the drum cartridge by the tabs at both ends, and slide the cartridge toward the
front of the printer. Then, firmly hold the cartridge by both ends, and lift the cartridge
out of the printer.

Important

• When removing the drum cartridge, make sure to firmly hold the cartridge to prevent it from falling on the

belt unit.

• Do not touch the interior of the printer. Some parts may be hot.
• Make sure to remove the drum cartridge before moving the printer. Otherwise, the toner may spill in the

printer.

• After removing the drum cartridge out of the printer, avoid exposure to strong light by putting it in a box or

aluminum bag or wrapping it with a thick cloth.

Note

• For information on how to remove the drum cartridge, refer to "Replacing the Drum Cartridge" (P. 129).

«
...
173
174
175
176
177
...
»

Summary of Contents for DocuPrint C1110 B


















































































































































































































Reviews:

No comments

Related manuals for DocuPrint C1110 B

Brand: m3d Pages: 23

Brand: m3d Pages: 26

Brand: TE Connectivity Pages: 2

Brand: TE Connectivity Pages: 2

Brand: Canon Pages: 2

PIXMA TS5300 Series

Brand: Canon Pages: 16

Pixma TR7600 Series

Brand: Canon Pages: 12

PIXMA MX420 Series

Brand: Canon Pages: 34

PIXMA MX700 Series

Brand: Canon Pages: 7

Brand: Canon Pages: 44

PIXMA MG3220 series

Brand: Canon Pages: 5

Brand: Canon Pages: 92

PIXMA TS6200 Series

Brand: Canon Pages: 100

Brand: Canon Pages: 68

Brand: Canon Pages: 745

SmartBase MPC400

Brand: Canon Pages: 76

Brand: Canon Pages: 59

Brand: Canon Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands