Fuji Xerox DocuCentreS2320 User Manual Download

Page: 61 / 257

Machine Components

Prod

erv
iew

Right Side, Rear

One tray module cover [B]

Open this cover to remove any jammed paper from Tray 2.

Tray 5 (bypass)

Load paper here. The tray can be extended.

Left cover [A]

Open this cover to remove any jammed paper.

Note

•

When the machine works properly, this cover is locked. To open this
cover, make sure to exit Sleep mode and turn the machine's power OFF.

No.

Component

Description

1
2

No.

Component

Description

Power switch

Switches the power of the machine on and off.

For more information, refer to "Power Source" (P.64).

Power cord connector

Connects the power cord.

Adjusting foot

Prevents the machine from toppling over. Move the machine to its
installation site and then rotate this adjuster in clockwise direction until it
touches a floor.

USB 2.0 interface connector
(Type B)

Connect a USB 2.0 cable.

10BASE-T/100BASE-TX
interface connector

Connect a network cable.

Summary of Contents for DocuCentreS2320

































































































































































































































































Search results

Summary of Contents for DocuCentreS2320

Reviews:

Related manuals for DocuCentreS2320

Brands by name

Popular brands

Fuji Xerox DocuCentreS2320, User Manual

Search results

Summary of Contents for DocuCentreS2320

Reviews:

Related manuals for DocuCentreS2320

Brands by name

Popular brands