Fuji Xerox DocuCentreS2320 User Manual Download

Page: 231 / 257

Paper Jams

231

roblem

lvin

Push on the center of the left cover, close it
slowly, and raise the Tray 5 (bypass).

Paper Jam in One Tray Module Cover [B]

Follow the steps below to clear paper jams inside the machine's one tray module cover.

Pull the release lever, and slowly open the one
tray module cover.

Remove the jammed paper.

Note

•

The paper may be jammed in the upper part
where it is difficult to see. Check thoroughly for
jammed paper.

•

If the paper tears, check to make sure there are
no remaining shreds in the machine.

Close the one tray module cover gently.

Paper Jam in Two Tray Module Cover [C]

Follow the steps below to clear paper jams inside the machine's two tray module cover.

Summary of Contents for DocuCentreS2320

































































































































































































































































Search results

Summary of Contents for DocuCentreS2320

Reviews:

Related manuals for DocuCentreS2320

Brands by name

Popular brands

Fuji Xerox DocuCentreS2320, User Manual

Search results

Summary of Contents for DocuCentreS2320

Reviews:

Related manuals for DocuCentreS2320

Brands by name

Popular brands