Fuji Xerox DocuCentreS2320 User Manual Download | Manualshive

Page: 217 / 257

background image

Error Code

217

P

roblem

S

o

lvin

g

12

Error Code

This section describes error codes.

An error message and error code (xxx-xxx) is displayed if printing terminated abnormally
because of an error, or a malfunction occurred in the machine.

Refer to the error codes in the following table to resolve problems.

Important •

If an error code is displayed, any print data remaining in the machine and information stored in the
machine's memory is not secured.

If an error code is displayed that is not listed in the following table, or if you cannot resolve
an error despite following the instructions described in the table, contact our Customer
Support Center. The contact number is printed on the label or card attached to the machine.

Error Code

Cause and Remedy

003-500

[Cause]

When using the Pages per Side function, the printout doesn't fit in
the paper with the specified reduction/enlargement factor.

[Remedy] Press the control panel's <Stop> button, and change the setting.

003-754

[Cause]

An IPS error occurred.

[Remedy] Press the control panel's <Stop> button, and cancel the job.

003-795

[Cause]

When enlarging/reducing a scanned document to the paper size
specified, the reduction/enlargement ratio exceeds the allowed
range.

[Remedy] Press the control panel's <Stop> button, and change the setting.

003-942

[Cause]

A document with a non-standard size is set in the document feeder.

[Remedy] Press the control panel's <Stop> button, and check the document.

003-956

[Cause]

A document with a non-standard size is set on the document glass.

[Remedy] Press the control panel’s <Stop> button, and check the document.

003-963

[Cause]

When [Auto] is set for [Paper Supply] for a copy job, the size of the
scan document is larger than the paper size that can be copied.

[Remedy] Press the control panel's <Stop> button, and change the setting.

003-972

[Cause]

Exceeded the maximum pages that can be scanned during a copy/
scan job.

[Remedy] Press the control panel's <Start> button to redo the operation or

press the <Stop> button to cancel the operation.

003-973

[Cause]

The image size is too large when enlarging/reducing a scanned
document that does not match the orientation of paper.

[Remedy] Take one of the following measures.



Reduce the magnification with [Reduce/Enlarge].



Change the orientation of paper or document.

004-345

[Cause]

An error occurred.

[Remedy] Switch off the machine power, make sure that the display is blank,

and then switch on the machine power. If the same message is
displayed again, contact our Customer Support Center.

«
...
215
216
217
218
219
...
»

Summary of Contents for DocuCentreS2320


































































































































































































































































Reviews:

No comments

Related manuals for DocuCentreS2320

imageCLASS Mf6160dw

Brand: Canon Pages: 64

imageCLASS MF6500 Series

Brand: Canon Pages: 132

imageCLASS MF5550

Brand: Canon Pages: 120

imageCLASS MF5630

Brand: Canon Pages: 85

imageCLASS MF5550

Brand: Canon Pages: 136

IMAGECLASS MF7400

Brand: Canon Pages: 40

imageCLASS MF5850dn

Brand: Canon Pages: 34

imageCLASS MF6500 Series

Brand: Canon Pages: 16

imageCLASS MF6540

Brand: Canon Pages: 82

imageCLASS MF5550

Brand: Canon Pages: 99

imageCLASS MF5630

Brand: Canon Pages: 24

imageCLASS MF5770

Brand: Canon Pages: 2

imagePRESS C7000VP Series

Brand: Canon Pages: 48

imageClass MF5650

Brand: Canon Pages: 40

imageCLASS MF5770

Brand: Canon Pages: 8

imageCLASS MF4880dw

Brand: Canon Pages: 36

imageCLASS MF4890dw

Brand: Canon Pages: 116

ImageCLASS MF4690

Brand: Canon Pages: 387

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands