Fuji Xerox DocuCentreS2320 User Manual Download | Manualshive

Page: 189 / 257

background image

Cleaning the Machine

189

M

a

int
e

na
nc
e

11

Cleaning Document Feeder Rollers

If the document feeder rollers become soiled, smudges may appear on copies, or scanned
documents and paper jams may occur.

To ensure clean copies at all times, clean the document feeder rollers about once a month.

Important •

Do not use benzene, paint thinner, or other organic solvents. Doing so may damage paint or coating
on plastic parts.

•

Cleaning the machine with an excessive amount of water may cause the machine to malfunction or
damage documents during copying or scanning.
Cleaning the machine with an excessive amount of water may cause the machine to malfunction or
damage documents during copying or scanning.

1

Lift the latch of the document feeder top cover
until it is completely open.

Note

•

When you fully open the cover, it enters a fixed
position. Open the cover gently.

2

While turning the rollers, wipe them with a soft
cloth moistened with water.

Important •

Do not use cleaning agents other than water or
neutral detergent.

•

Use a cloth firmly wrung to prevent water drops
from falling into the machine. If water gets into
the machine, it may cause the machine to
malfunction.

Note

•

If you cannot remove dirt easily, gently wipe
the rollers with a soft cloth moistened with a
small amount of neutral detergent.

3

Close the document feeder top cover until it clicks into place, and confirm that there is no
space between the near or far side of the cover and the document feeder.

«
...
187
188
189
190
191
...
»

Summary of Contents for DocuCentreS2320


































































































































































































































































Reviews:

No comments

Related manuals for DocuCentreS2320

Brand: Canon Pages: 16

IR5000 - iR B/W Laser

Brand: Canon Pages: 86

Brand: Canon Pages: 48

Brand: Roland Pages: 36

Brand: Oce Pages: 222

Brand: Xerox Pages: 8

Brand: Tally Dascom Pages: 2

Pro-LX Pro-LX Laminating Card...

Brand: FARGO electronics Pages: 228

WorkCentre 7970

Brand: Xerox Pages: 268

Brand: Ricoh Pages: 2

Blaster ADVANTAGE

Brand: CognitiveTPG Pages: 20

Brand: Wasp Pages: 46

VersaUV LEF2-300

Brand: Roland Pages: 264

imagePROGRAF PRO-6600

Brand: Canon Pages: 939

Brand: Compart Pages: 28

Brand: Xiaomi Pages: 7

Brand: Printronix Pages: 50

Brand: Printekmobile Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands