Fuji Xerox DocuCentre S1810 User Manual Download Page 49

Page: 49 / 202

Machine Components

roduc

t O
v

Right Side, Rear

Left cover [A]

Open this cover to remove any jammed paper.

Note

•

When the machine works properly, this cover is locked. To open
this cover, make sure to exit Sleep mode and turn the machine's
power OFF.

No.

Component

Description

Power switch

Switches the power of the machine on and off.

For more information, refer to "Power Source" (P.52).

Power cord connector

Connects the power cord.

Adjusting foot

Prevents the machine from toppling over. Move the machine to its
installation site and then rotate this adjuster in clockwise direction until it
touches a floor.

USB 1.1/2.0 interface
connector (Type B)

Connect a USB 1.1/2.0 cable.

10BASE-T/100BASE-TX
interface connector

Connect a network cable.

Note

•

The 10BASE-T/100BASE-TX interface connector is available when
the optional Simple Network Print Kit is installed.

No.

Component

Description

Summary of Contents for DocuCentre S1810










































































































































































































Search results

Summary of Contents for DocuCentre S1810

Reviews:

Brands by name

Popular brands

Fuji Xerox DocuCentre S1810, User Manual

Search results

Summary of Contents for DocuCentre S1810

Reviews:

Brands by name

Popular brands