Fuji Xerox DocuCentre S1810 User Manual Download Page 30

Page: 30 / 202

2 Environment Settings

t Se

ttings

Using the Ethernet Interface

The machine supports 100BASE-TX and 10BASE-T Ethernet interfaces.

Note

•

The Ethernet interface is available when the Simple Network Print Kit is installed on the
machine.

To connect the Ethernet interface:

Press the power switch to the [ ] position to
turn the power OFF.

Note

•

Check the display of the status machine
diagram is turned off.

Connect a network cable to the Ethernet
interface connector.

Note

•

Prepare a network cable suitable for your
network connection. When you replace the
network cable, contact our Customer
Support Center.

Press the power switch to the [ | ] position to
turn the power ON.

Summary of Contents for DocuCentre S1810










































































































































































































Search results

Summary of Contents for DocuCentre S1810

Reviews:

Brands by name

Popular brands

Fuji Xerox DocuCentre S1810, User Manual

Search results

Summary of Contents for DocuCentre S1810

Reviews:

Brands by name

Popular brands