Fuji Xerox DocuCentre S1810 User Manual Download Page 149

Page: 149 / 202

Machine Problems

149

lem S

lving

Machine Problems

Check the machine's status again if you suspect a malfunction.

Symptom

Possible Cause

Remedy

The machine is
not powered on.

Is the power switched ON?

Switch the power ON.

Refer to "Power Source" (P.52).

Is the power cord plugged
into the power outlet?

Switch the power OFF and make sure the
power plug is inserted securely. Then
switch the power ON.

Is the power cord
disconnected from the
machine?

Does the AC outlet supply
power properly?

Connect another appliance to the outlet to
verify the power supply.

The <Error>
indicator is
blinking.

The system of the machine
or the components installed
may have a trouble.

Switch the power OFF, then ON again. If
the problem persists, contact our Customer
Support Center.

The <Error>
indicator is lit.

Is paper or document
jammed?

Remove the jammed paper or document.

Refer to "Paper Jams" (P.179).
Refer to "Document Jams" (P.184).

Is the machine front cover
or another cover open?

Follow the instructions in the displayed
error code to take the required action.

Refer to "Error Code" (P.172).

The display is
dark.

Is the <Energy Saver>
button lit?

The machine is in an energy saver mode.
Press the control panel's <Energy Saver>
button to turn off the energy saver mode.

Unable to print
or copy.

Is there an error code
displayed in the control
panel's display?

Follow the instructions in the displayed
error code to take the required action.

Refer to "Error Code" (P.172).

Is the power cord
connected?

Switch the power OFF and make sure the
power plug is inserted securely into the
power outlet. Then switch the power ON.

The <Data>
indicator does
not light even
though you
instructed the
machine to print.

Is the interface cable
connected?

Check the interface cable connection.

Refer to "Interface Cables" (P.29).

Is the computer's
environment correctly set?

Check the computer environment such as
print driver settings.

Is the required port status
set to [Enabled]?

Check the status of the port to use, and
then set the port status to [Enabled].

Refer to "Activating the Communication Port
To Use" (P.32).

Unable to print
although a print
job is instructed
to Bypass tray.

Is the specified paper size
loaded in the tray?

Follow the instructions in the displayed
error code to place paper of the correct
size, and then try again.

Refer to "Error Code" (P.172).
Refer to "Loading Paper in Bypass Tray"
(P.76).

Summary of Contents for DocuCentre S1810










































































































































































































Search results

Summary of Contents for DocuCentre S1810

Reviews:

Brands by name

Popular brands

Fuji Xerox DocuCentre S1810, User Manual

Search results

Summary of Contents for DocuCentre S1810

Reviews:

Brands by name

Popular brands