Fuji Xerox DocuCentre S1810 User Manual Download Page 114

Page: 114 / 202

8 Tools

114

To
ols

System Settings Procedure

This section describes the overview of how to change the machine's default settings

and check the machine information.

Important •

If there are any current or pending jobs, you cannot enter the System Administration mode.

•

During the System Administration mode, the following operations cannot be performed.

Receiving a print job, and starting a print or scan job.

Enter the System Administration Mode

Press and hold the <Log In/Out> button for
more than 4 seconds until the screen below is
displayed.

Use the numeric keypad to enter the password, and then press the <Start> button.

Note

•

The password is initially set to "11111" (five digits of "1").

•

The password can be changed.
For more information, refer to "System Settings" (P.116).

•

The <Log In/Out> button lights up when the machine enters the System Administration
mode.

The program number input screen appears,

and shows the letter [P].

<Log In/Out> button

Summary of Contents for DocuCentre S1810










































































































































































































Search results

Summary of Contents for DocuCentre S1810

Reviews:

Brands by name

Popular brands

Fuji Xerox DocuCentre S1810, User Manual

Search results

Summary of Contents for DocuCentre S1810

Reviews:

Brands by name

Popular brands