manualshive.com logo in svg

Fuji Xerox ApeosPort-V C2276, Administrator'S Manual

Share
Download
Fuji Xerox ApeosPort-V C2276 Administrator'S Manual Download Page 651

Specifications

651

A

ppe

n

d

ix

16

Direct Fax Function

Internet Fax Function

Recording Paper Size

Maximum

:

A3, 11 x 17"

Minimum

:

A5

Transmission Time

2 seconds or more but below 3 seconds

Important •

When transmitting an A4 size 700-character document in the 
standard quality (8 x 3.85 lines/mm) and high speed mode (28.8 kbps 
or above: JBIG). This is only the transmission speed for image 
information and does not include the controlling time for the 
communication. Note that the actual transmission time depends on 
the content of documents, the machine that the recipient uses, and 
the status of the communication line.

Transmission Mode

ITU-T G3

Scanning Resolution

Standard

:

8 x 3.85 lines/mm
200 x 100 dpi

Fine

:

8 x 7.70 lines/mm
200 x 200 dpi

Superfine (400dpi) : 16 x 15.4 lines/mm

400 x 400 dpi 

Superfine (600dpi) : 600 x 600 dpi

Coding Method

MH / MR / MMR / JBIG

Transmission Speed

G3 :33.6/31.2/28.8/26.4/24.0/21.6/19.2/16.8/14.4/12.0/9.6/7.2/4.8/
2.4kbps

No. of Fax Lines

PSTN, PBX (G3 maximum 3 lines)

Sending Document Size

A3, B4, A4

Fax Resolution

Same as the Scanning Resolution for Fax Function

Transmission Speed

Same as the Fax Function

Applicable Lines

Same as the Fax Function

Operating System

Microsoft® Windows Server® 2003,
Microsoft® Windows Server® 2008,
Microsoft® Windows Vista®,
Microsoft® Windows® 7,
Microsoft® Windows® 8,

Microsoft

®

 Windows

®

 8.1,

Microsoft® Windows Server® 2003 x64,
Microsoft® Windows Server® 2008 x64,
Microsoft® Windows Server® 2008 R2 x64,
Microsoft® Windows Vista® x64,
Microsoft® Windows® 7 x64,
Microsoft® Windows Server® 2012 x64,

Microsoft

®

 Windows Server

®

 2012 R2 x64,

Microsoft® Windows® 8 x64,

Microsoft

®

 Windows

®

 8.1 x64,

Mac OS X 10.5/10.6, Mac OS X 10.7 Lion, OS X 10.8 Mountain Lion, 
OS X 10.9 Mavericks, OS X 10.10 Yosemite

Note

•

For information about the latest supported OS, refer to the Fuji Xerox 
Web site.

Sending Document Size

A3, B4, A4

Scanning Resolution

Same as the Fax Function

Summary of Contents for ApeosPort-V C2276
















































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands