manualshive.com logo in svg

Fuji Xerox ApeosPort-V C2276, Administrator'S Manual

Share
Download
Fuji Xerox ApeosPort-V C2276 Administrator'S Manual Download Page 491

Network-related Problems

491

Pro

b

lem

 So
lv

in

g

15

Internet/Intranet Connection Problems

The possible causes and remedies for problems when connecting to the Internet or intranet 
are as follows:

When connection to the Internet/Intranet fails

Cannot transmit e-mail (E-mail 
Notification Service, Internet 
Fax, and E-mail).

Is the E-mail address for the machine configured?

Is [E-mail Notification Service] set to [Enabled]? (For E-mail 
Notification Service).

Is [Send E-mail] set to [Enabled]?

Is the IP address for the SMTP server configured correctly?

Are the settings for notification of transmission configured 
correctly? (for E-mail Notification Service)
Confirm the settings on the [Properties] tab of CentreWare 
Internet Services.

Is the destination address entered correctly?

Is the SMTP server operating properly?
Consult your network administrator.

Cause

Remedy

The Authentication feature 
used on the remote server is 
not supported by the machine.

Only Basic Authentication is supported by the machine. The 
machine does not support NTLM/digest.
For security purposes, change to the Authentication feature 
using SSL.

The remote linkage services 
used does not support the 
model or accessories of the 
machine.

Purchase products/models/accessories supported by the remote 
linkage services.

The IP address is incorrect.

Confirm the IP address. If the IP address is incorrect, either set a 
static IP address or resolve the IP address using DHCP or AutoIP.

The IP gateway address is 
incorrect.

Set the correct IP gateway address when connecting to the 
proxy server, or to a Web server via the IP gateway.

The subnet mask is incorrect.

Set the correct subnet mask corresponding to your environment.

The DNS server address is 
incorrect.

Confirm the DNS server address.

The DNS server selected 
cannot resolve the address.

Select a DNS server that can resolve the address.

When connecting via the proxy server
Set the IP address of a DNS server that can resolve the 
address of the proxy server.

When not connecting via the proxy server
Set the IP address of a DNS server that can resolve the 
destination address.

Symptom

Remedy

Summary of Contents for ApeosPort-V C2276
















































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands