manualshive.com logo in svg

Fuji Xerox ApeosPort-V 4070, Administrator'S Manual

The Fuji Xerox ApeosPort-V 4070 is a versatile multifunction printer designed for office use. To optimize its features, the Administrator's Manual is a comprehensive guide that can be downloaded for free from our website, providing step-by-step instructions and configuration options to enhance productivity and efficiency.

Share
Download
background image

16 Appendix

682

A

p

pe
ndi
x

16

z

VoIP gateways do not work on IPsec communication.

z

VoIP gateways do not work in an IPv6 environment.

z

If settings other than specified by Fuji Xerox are configured for a dial peer or a voice port 
on a VoIP gateway, the VoIP gateway does not work.

z

If a part of transferred data is lost on a network, a part of image may be missing or be 
getting stacked. To avoid these, the ECM mode is effective. The machine can always use 
the ECM mode, however, you cannot use the mode depending on the VoIP gateway 
settings. Consult your network administrator whether the ECM mode is available.

NAT/NAPT

z

Communication protocols that transmit UPnP, TURN, STUN, ICE, and UDP hole punching 
in SIP communications are not supported. IP Fax (SIP) does not work in an environment 
that uses NAT/NAPT devices including ALG.

Notes and Restrictions when Connecting with Internet Service Provider

This section describes notes and restrictions to observe when using features that transmit e-
mails or Internet faxes using an Internet service provider (ISP).

The features related to e-mail are as follows:

z

E-mail

z

E-mail Notification Service

z

Print E-mail

z

Internet Fax

„

Notes and Restrictions on Accessing ISP

Observe the following notes and restrictions when connecting the machine to ISP:

z

Dial-up connection is not supported. Continuous connection is required.

z

Connect the machine in an environment using IP masquerade. Assigning a global IP 
address to the machine is not supported.

z

Be sure to assign an exclusive e-mail account to the machine for POP reception. Sharing 
an e-mail account with other users may cause troubles.

z

Be sure to set size limitation for sending e-mail. Although the applicable e-mail size may 
vary depending on the ISP used, we recommend that you set a small value.

z

Although continuous connection other than ADSL or cable connection is also supported, 
the reception of image data significantly burdens the machine.

z

SMTP reception is not supported. This machine supports only POP reception.

z

When installing the machine in an environment that is operating a mail transfer agent 
(MTA) in a private segment, set the machine to adapt to the operation system being used.

z

For information about supported ISPs, contact our Customer Support Center.

z

When received via POP, the fax cannot be sent using the Fax Gateway feature. This is 
because POP receiving does not forward an Internet fax document received by e-mail to 
the fax machine.

„

Feature Specifications

Details of the features related to e-mail are as follows:

Summary of Contents for ApeosPort-V 4070
















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ApeosPort-V 4070

Panasonic KX-MC6260E Quick Reference Manual preview
KX-MC6260E
Brand: Panasonic Pages: 24
Oki 10i Help Manual preview
10i
Brand: Oki Pages: 40
Panasonic Workio DP-1820E Quick Manual preview
Workio DP-1820E
Brand: Panasonic Pages: 38
QMS 4525 Print System User'S Manual preview
4525 Print
Brand: QMS Pages: 180
Pantum M6500 series Faq preview
M6500 series
Brand: Pantum Pages: 126
ABLE Ap1400 Programmer'S Manual preview
Ap1400
Brand: ABLE Pages: 42
Oki C542 Advanced Manual preview
C542
Brand: Oki Pages: 255
Tally t2145 Operator'S Manual preview
t2145
Brand: Tally Pages: 106
Oce TDS860 User Manual preview
TDS860
Brand: Oce Pages: 330
Phoenix Contact 1184146 User Manual preview
1184146
Brand: Phoenix Contact Pages: 52
G&G IMAGE L2550DW Series User Manual preview
IMAGE L2550DW Series
Brand: G&G Pages: 147
Konica Minolta bizhub pro 1200P User Manual preview
bizhub pro 1200P
Brand: Konica Minolta Pages: 333
Xerox Phaser 3600 Instruction preview
Phaser 3600
Brand: Xerox Pages: 23
WOOSIM PORTI-W25 Operator'S Manual preview
PORTI-W25
Brand: WOOSIM Pages: 29
Oki B 4600n User Manual preview
B 4600n
Brand: Oki Pages: 106
SATO FX3-LX Driver Manual preview
FX3-LX
Brand: SATO Pages: 100
Rego RG-MTP58B User Manual preview
RG-MTP58B
Brand: Rego Pages: 28
LI-COR ODYSSEY Sa Operator'S Manual preview
ODYSSEY Sa
Brand: LI-COR Pages: 50

Brands by name

Popular brands

Load more brands