manualshive.com logo in svg

Fuji Xerox ApeosPort-V 4070, Administrator'S Manual

The Fuji Xerox ApeosPort-V 4070 is a versatile multifunction printer designed for office use. To optimize its features, the Administrator's Manual is a comprehensive guide that can be downloaded for free from our website, providing step-by-step instructions and configuration options to enhance productivity and efficiency.

Share
Download
background image

Installation When Using Parallel Port

307

P

rint
e

r En

v

iro
nmen

t Set

tin

g

s

7

z

PJL

Enable this setting to accept a job with PJL commands.

The PJL commands are independent of any printer languages. A printer language used in 
the data received next can be set independently of the current printer language.

z

Auto Eject Time

Set the time that the data so far received by the machine is automatically printed since 
data is no longer sent to the printer.

z

Adobe Communication Protocol

Set the protocol defining the communications method between PostScript printers and a 
host. 

z

Bi-directional Communication

Configure the parallel port for either half duplex transmission or full duplex transmission. 

Note

•

Adobe Communication Protocol can be configured when the Adobe PostScript 3 Kit (optional) is 
installed.

•

Do not change the default settings for normal use. You may, however, need to change some settings 
depending on the operating system of your computer. 

5

Select [Close] repeatedly until the [Tools] screen is displayed.

6

Select [Close].

Note

•

Rebooting the machine may be required depending on the settings. When a message displayed on 
the screen, follow the message and reboot the machine.

7

Print a configuration report to confirm that the parallel port is enabled.

For information on how to print a configuration report, refer to "Print Reports" (P.90).

8

Turn off the computer to be connected to the machine.

9

Connect a parallel interface cable to the parallel interface on the computer.

For information on how to connect a parallel interface cable, refer to "Using the Parallel Interface" (P.22).

10

Start the computer.

Step 3 Configuration on the Computer

The following describes the configuration procedures for the computer. 

To print from the machine, you need to install a print driver on your computer.

For information on the supported operating systems, refer to "Supported Operating Systems" (P.305). 

For information on the driver installation procedure, refer to the manual contained in the Media (Software/Product 
Manual).

CentreWare Internet Services Setting Items

You can configure the following setting items using CentreWare Internet Services:

For details on the setting items, click [Help] at the upper right corner of the CentreWare Internet Services screen to see help.

For information on how to start CentreWare Internet Services, refer to "Starting CentreWare Internet Services" (P.298).

Important •

To display the online help for CentreWare Internet Services, users need to have the environment to 
connect to the Internet. The communication fee shall be borne by you.

z

Receiving buffer size for the parallel interface
([Properties] > [General Setup] > [Memory Settings] > [Parallel])

z

Port Settings

Summary of Contents for ApeosPort-V 4070
















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ApeosPort-V 4070

Canon iR1018 Portable Manual preview
iR1018
Brand: Canon Pages: 86
Canon iR1018 Installation Procedure preview
iR1018
Brand: Canon Pages: 20
Xerox 665 User Manual preview
665
Brand: Xerox Pages: 89
Olivetti PG L2035 Quick Installation Manual preview
PG L2035
Brand: Olivetti Pages: 16
HPRT HM-A300S Quick Start Manual preview
HM-A300S
Brand: HPRT Pages: 2
Konica Minolta AccurioPrint 2100 Shortcut Manual preview
AccurioPrint 2100
Brand: Konica Minolta Pages: 32
Lexmark C910 Finisher Manual preview
C910 Finisher
Brand: Lexmark Pages: 11
Oce cm2522 User Manual preview
cm2522
Brand: Oce Pages: 222
Xerox Phaser 8400 Service Manual preview
Phaser 8400
Brand: Xerox Pages: 29
Xerox Phaser 6700V/DX User Manual preview
Phaser 6700V/DX
Brand: Xerox Pages: 162
3nStar PPT205 User Manual preview
PPT205
Brand: 3nStar Pages: 8
NEC 4650NX - SuperScript Color Laser Printer Network Manual preview
4650NX - SuperScript Color Laser Printer
Brand: NEC Pages: 74
Roland VersaUV LEF2-300 Service Notes preview
VersaUV LEF2-300
Brand: Roland Pages: 264
DataCard MPR5000 Brochure preview
MPR5000
Brand: DataCard Pages: 4
Olivetti d-COLOR P2021 Operation Manual preview
d-COLOR P2021
Brand: Olivetti Pages: 197
CAB Apollo Series Programming Manual preview
Apollo Series
Brand: CAB Pages: 222
Philips LaserMFD 6050 WLAN Specifications preview
LaserMFD 6050 WLAN
Brand: Philips Pages: 2
Lexmark Z815 Setup Manual preview
Z815
Brand: Lexmark Pages: 2

Brands by name

Popular brands

Load more brands