manualshive.com logo in svg

Fuji Xerox ApeosPort-V 4070, Administrator'S Manual, Page: 201 / 719

Share
Download
Fuji Xerox ApeosPort-V 4070 Administrator'S Manual Download Page 201

Connectivity & Network Setup

201

Tools

5

- When [SHA-256] is selected: DocuWorks 8.0 or later

„

XPS Signature

Select the setting for XPS Signature from [Do not add signature], [Always add invisible 
signature], or [Select during send]. 

IPsec

Note

•

This item is not displayed when Secondary Ethernet (optional) is installed on the machine.

„

IPsec Settings

Configure the IPsec settings to use encryption or signature option on the transmission of e-
mail or fax.

Note

•

For [IKE Authentication Method], [Preshared Key], [DH Group], and [PFS Settings], consult your 
network administrator.

z

IKE Authentication Method

Set the IKE authentication method. Select from [Authenticate by Preshared Key] or 
[Authenticate by Digital Signature].

z

Preshared Key

Enter a preshared key. This setting is valid when [IKE Authentication Method] is set to 
[Authenticate by Preshared Key].

z

Device Certificate

Select a certificate for IPsec communications.

Select a certificate when [IKE Authentication Method] is set to [Authenticate by Digital 
Signature]. A self-signed certificate created by CentreWare Internet Services cannot be 
used.

For more information on a certificate, refer to "Types of Certificate" (P.370).

z

IPsec Communication

Select whether or not to enable IPsec communications.

z

IKE SA Life Time

Specify IKE SA lifetime from 5 to 28800 minutes in 1 minute increments. 

Note

•

The value must be greater than the value set in [IPsec SA Life Time].

z

IPsec SA Life Time

Specify IPsec SA lifetime from 300 to 172800 seconds in 1 second increments. 

Note

•

The value must be smaller than the value set in [IKE SA Life Time].

z

DH Group

Set DH group. Select from [G1] or [G2].

z

PFS Settings

Select whether or not to enable PFS.

z

Destination IPv4 Address

Set the IPv4 address of the destination.

When entering an IP address, enter the address in the format "xxx.xxx.xxx.xxx", where 
"xxx" is a numeric value from 0 to 255.

z

Destination IPv6 Address

Set the IPv6 address of the destination.

Summary of Contents for ApeosPort-V 4070
















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments