Fuji Micro Genforce Baumr-AG BM-700i User Manual Download Page 9

Page: 9 / 30

Petrol Powered Inverter Generators

E&OE

Before Use Checklist

Ensure that you carry out all procedures below before

starting the engine or operating the equipment. All

procedures described are generic in nature and slight variations between

different models may exist.

Failure to follow the checklist and carry out the procedures correctly may

result in making the product warranty void

. The product is NOT supplied with engine oil, although traces

of oil from the manufacturing process may be present. It is essential to add adequate engine oil of the correct

type to the engine before use – see

Checking and Changing Engine Oil

Failure to add engine oil will void

the product warranty

Engine Oil

Four-stroke engines require engine oil in the crankcase for lubrication of internal components. Severe or

irreparable damage may occur if the engine is allowed to run without engine oil. The engine oil level requires

regular maintenance. Check the engine oil level and ensure that the oil level is at or just under the maximum

level indicator.
Some machines may feature an oil level sensor that will prevent the engine being started or automatically

stop the engine if the oil level falls below an acceptable level. This system, however, is not to be solely relied

upon.

Always check that the engine oil level is at or near the "MAX" indicator before starting the

engine

. See

Checking and Changing Engine Oil

Air Filter

The air filter is used to prevent dirt and other particles from possibly entering the engine and causing internal

damage to it. The air filter requires regular maintenance.
Always check the air filter before starting the engine. See

Checking, Cleaning and Replacing the Air Filter

Fuel

Petrol/fuel/gasoline is extremely flammable – keep clear of naked flames or other ignition

sources. • The engine must be cool before refuelling.

Adequately fill the fuel tank with the correct fuel type.

•

Use non-ethanol unleaded petrol (higher RON values will provide best engine performance). Do not use

old or contaminated fuel.

To fill or top up fuel:
1. Place the machine in an upright position on a flat and level surface.
2. Clean the machine around the fuel filler so that no dirt or other material enters the tank when the cap is

removed.

3. Remove (rotate left) the fuel filler cap.
4. Using a funnel, carefully fill the tank with fuel. Do not fill above the top of the strainer (if equipped) or

otherwise overfill the tank.

5. When finished, reinstall (rotate right) the fuel filler cap until firm. Wipe away any residual fuel from the

machine. If fuel has been spilt, move the machine away from the spillage before starting the engine.

Video Tutorial:

Inverter Generator Set-Up

FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG FUJI-MICRO GENFORCE BAUMR-AG