FUJI CONTROLS IN-100 Instruction Manual Download Page 58

Page: 58 / 61

CC-Link

What is "CC-Link"?

Wire-saving feature of CC-Link allows any input/output of IN-100 to be turned on or off or

acquire hold load values or real time load values.

CC-Link version of IN-100 is 1.10, and the type of station is remote device station.

How to set

1. Press MENU key.

2. Use



⋀



⋁

key to select

System Setting

3. Press SET key.

4. Use



⋀



⋁

key to select

CC-Link

5. Press SET key.

6. Confirm

4 Station

is selected.

7. Press SET key and confirm the cursor has turned green.

8. Press SET key again.

9. Use



⋀



⋁

key to select

Station Number

. (default: 01)

10. Press SET key and confirm the cursor has turned green.

11. Press SET key again to select Transmission Speed with



⋀



⋁

key. (default: 10M)

12. Press SET key and confirm the cursor has turned green.

13. Press SET key again to select Return Data Format with



⋀



⋁

key. (default: BCD)

14. Press SET key and confirm the cursor has turned green.

15. Press SET key again to select Select Memory by with



⋀



⋁

key. (default: Manual)

16. Press SET key and confirm the cursor has turned green.

17. Press SET key again.

18. Confirm

Internal ROM

is selected.

19. Press SET key and confirm the cursor has turned green.

20. Press SET key again.

21. The Link Status is shown. Confirm appropriate transmission has been done.

22. Press RESET key to complete this operation.

Summary of Contents for IN-100






























































Search results

Summary of Contents for IN-100

Reviews:

Related manuals for IN-100

Brands by name

Popular brands

FUJI CONTROLS IN-100, Instruction Manual

Search results

Summary of Contents for IN-100

Reviews:

Related manuals for IN-100

Brands by name

Popular brands