FUJI CONTROLS IN-100 Instruction Manual Download Page 51

Page: 51 / 61

Setting Memory

What is "Setting Memory"?

This function allows you switch over 4 patterns of the hold mode, or high limit judgment

(HI), low limit judgment (LO), set load arrival output (OF), and Hold Mode.

When By signal is selected, change external input/output terminal No. 16 SEL1 or No. 17

SEL2 with BCD input.

When By menu is selected, select by setting the Setting Memory of IN-100.

How to set

BY SIGNAL

1. Press MENU key.

2. Use



⋀



⋁

key to select

System Setting

3. Press SET key.

4. Use



⋀



⋁

key to select

Setting Memory

5. Press SET key.

6. Use



⋀



⋁

key to select

By signal

. (default: By menu)

7. Press SET key and confirm the cursor has turned green.

8. Press SET key again to complete this operation.

Summary of Contents for IN-100






























































Search results

Summary of Contents for IN-100

Reviews:

Related manuals for IN-100

Brands by name

Popular brands

FUJI CONTROLS IN-100, Instruction Manual

Search results

Summary of Contents for IN-100

Reviews:

Related manuals for IN-100

Brands by name

Popular brands