background image

SERVICE MANUAL 

HEATED LANDING ZONE (HLZ 18 AND HLZ 22) 

 

Frymaster L.L.C., 8700 Line Avenue 71106, P.O. Box 51000, Shreveport, Louisiana 71135-1000 

318-865-1711       FAX 318-862-2394 

 

Printed in the United States Service 

Hotline 

 

 1-800-24-FRYER 

819-5659 

(02/07) 

 

 

This equipment chapter is to be inserted in the Equipment Manual. 

 

 

 

 
 
 
 
 
 

TABLE OF CONTENTS 

1. WARRANTY 

STATEMENT ............................................................................................................ 1 

1.1 

WARRANTY PROVISIONS - HEATED LANDING ZONE ...................................................................................... 1 

1.2 PARTS 

RETURN ................................................................................................................................................... 1 

1.3 WARRANTY 

EXCLUSIONS................................................................................................................................... 1 

2. PARTS 

ORDERING 

AND 

SERVICE INFORMATION .................................................................... 2 

3. HEATED 

LANDING ZONE ............................................................................................................. 3 

4. INSTALLATION/SETUP ................................................................................................................. 3 

5. OPERATION ................................................................................................................................... 3 

6.  HLZ MODEL/COMPONENT IDENTIFICATION ............................................................................. 4 

7. HLZ 

COMPUTER 

OPERATION AND PROGRAMMING ............................................................... 5 

7.1 PROGRAMMING TEMPERATURE ....................................................................................................................... 5 

7.2 OPERATION .......................................................................................................................................................... 6 

8.  HLZ OPERATOR TROUBLESHOOTING ...................................................................................... 8 

9.   SERVICE  INFORMATION .….…………..……………………………………………………..…..…   9 

9.1  PARTS LIST…….……………………………………………………………………………………………………………....9 

9.2  INTERIOR VIEW OF AN HLZ ….…………………….……………………………………………………………………….9 

9.3  PROCEDURES..…………………………………………………………………………………………..…………..…....… 11 

10  DIAGNOSTIC TESTS…………………………………………..…………………………….…..…..….. ........................... 15 

11  WIRING DIAGRAM………………………………………………………..……………….…………….............................. 18 

 

 
 
 
 

MANUFACTURED BY FRYMASTER, L.L.C. 

P.O. BOX 51000 

SHREVEPORT, LOUISIANA  71135-1000 

PHONE 1(318)865-1711 

1 (800) 24 FRYER 

Summary of Contents for Heated Landing Zone HLZ 18





















Reviews: