FrSky Electronic Co., Ltd www.frsky-rc.com Contact us : [email protected]
Add:F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
FrSky is continuously adding features and improvements to our products. To get the most from your product, please check
the download section of the FrSky website www.frsky-rc.com for the latest update firmware and manuals
Failsafe setting via transmitter for channel output position is just for D16 RF mode. Besides, Failsafe setting via transmitter
has higher priority to that via receiver.
•
For Horus X12S/X10S/X10, turn on the transmitter, go to MDL—FAILSAFE.
2. Set on the receiver
•
Short press F/S button while moving channel positions to a preset value after binding.
There are 3 failsafe modes: No pulse, Hold, Custom.
•
No pulse: On loss of signal, the receiver produces no pulses on any channle. To apply the mode, select it in the menu and wait 9
seconds for the failsafe to take effect.
•
Hold: The model will maintain the last position after loss of signal. To apply the mode, select it in the menu and wait 9 seconds for
the failsafe to take effect.
Failsafe is a useful feature which is for a preset channel output position whenever control signal is lost for a period. Failsafe for receiver
supporting D16 RF mode can be set via transmitter’s interface, which supports no pulse, hold and custom for each channel.
Follow the steps below to set failsafe
1. Set on the transmitter
•
For Taranis X9D/X9D Plus and Taranis Q X7S/X7, turn on the transmitter, go to MODEL SETUP—Internal RF/External RF—Failsafe.
F
ailsafe
Introduction manual for FrSky RX8R PRO
H
ow to switch operating mode
Normal mode of RX8R PRO is D16.
D8 mode only operates when the signal pins of CH7&CH8 are jumped before bind.
H
ow to switch servo frame rate
Normal servo frame rate is 18ms(FS-Normal Speed Mode).
High Speed Mode (9ms) only operates when the signal pins of CH5&CH6 are jumped before bind.
FrSky Electronic Co., Ltd www.frsky-rc.com Contact us : [email protected]
Add:F-4,Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China Technical Support: [email protected]
Introduction manual for FrSky RX8R PRO
•
Custom: The customized position of each individual channel. The model will move to the pre-set position after loss of signal. Move
the cursor to set and press ENTER, you will see FAILSAFE SETTING screen below. Move the cursor to the channel you want to set
failsafe on, and press ENTER. When moving the corresponding sticks or switches, you will see the channel bar moving. Move the channel
bar to the place you want for failsafe and long press ENTER to finish the setting. Wait 9 seconds before failsafe taking effect.
F
CC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate
the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
