manualshive.com logo in svg

Frontgate 140180B, Manual, Page: 5 / 9

Share
Download
Frontgate 140180B Manual Download Page 5

5

 

 

 
9. Carefully slide UMBRELLA (A) onto UMBRELLA 
MOUNT (B).  See Diagram 9. 

Diagram

 

9

 

 

 

 
10.  LINE UP the ROTATION HANDLE (G) around 
the lowest hole in the UMBRELLA (A) POLE, just 
above the BASE ASSEMBLY.  See Diagram 10a. 
 
11. Slide the PIVOT TUBE (H) thru one side of the 
ROTATION HANDLE and thru the UMBRELLA (A) 
POLE.  See Diagram 10b.  
 
12. On the OPPOSITE side of the UMBRELLA (A) 
POLE, SLIDE the ROTATION HANDLE BOLT (I-1) 
thru the ROTATION HANDLE WASHER (I-2) and 
then into the THREADED end of the PIVOT TUBE 
(H).  See Diagram 10c. 
 
13.  TIGHTEN with the ALLEN KEY (M).  See 
Diagram 10d. 

Diagram

 

10a

                                        

Diagram

 

10b

 

 

Diagram

 

10c

                                       

Diagram

 

10d

 

 

 
14. Install the CRANK HANDLE (J) by SLIDING it 
onto the CRANK MECHANISM, which is located on 
the UMBRELLA (A) POLE.  It should snap in place.  
No hardware is needed.  See Diagram 11. 
 

Diagram

 

11

 

 

 

 

 

Summary of Contents for 140180B










Reviews:

No comments