Front Runner SlimSport KSFR002 Manual Download Page 1

KSFR002_REV_A03

© 2022 FRONT RUNNER VEHICLE OUTFITTERS

front runner

KSFR002

ENG

1

FORD RANGER T6 

/

 WILDTRAK 

/

 RAPTOR 

(

2012

-

CURRENT

)

 SLIMSPORT ROOF RACK KIT 

Don’t be a hero and muscle through this installation without reading these fitting instructions first! Improper installation of this gear may void certain 

aspects of your warranty. 
Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components. 

A complete kit will contain:
1. A Front Runner SlimSport Kit

This document will guide you through the assembly of the mounting system and assist you in fitting the roof rack tray or load bars to your specific 

vehicle.
Please refer to the next page for a list of all the components, quantities and tools required. 

READ ME FIRST

START HERE!

IMPORTANT WARNING

!

IT  IS  CRITICAL  THAT  ALL  FRONT  RUNNER  PRODUCTS  BE  PROPERLY  AND  SECURELY  ASSEMBLED  AND  ATTACHED  TO  YOUR  VEHICLE.  IMPROPER  ATTACHMENT  COULD  
RESULT  IN  AN  AUTOMOBILE  ACCIDENT,  AND  COULD  CAUSE  SERIOUS  BODILY  INJURY  OR  DEATH.  YOU  ARE  RESPONSIBLE  FOR  ASSEMBLING  AND  SECURING  ALL  FRONT 
RUNNER  PRODUCTS  TO  YOUR  VEHICLE,  CHECKING  THE  ATTACHMENTS  PRIOR  TO  USE,  AND  PERIODICALLY  INSPECTING  THE  PRODUCTS  FOR  ADJUSTMENT,  WEAR  AND 
DAMAGE.  THEREFORE,  YOU  MUST  READ  AND  UNDERSTAND  ALL  OF  THE  INSTRUCTIONS  AND  PRECAUTIONS  SUPPLIED  WITH  YOUR  FRONT  RUNNER  PRODUCT  PRIOR  TO 
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY 
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.

NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.

Please call us if you have any questions about the installation of this product.

Summary of Contents for SlimSport KSFR002









Reviews: