Friulinox Cube Series Service Manual Download

Page: 74 / 89

“go to

TABLE OF CONTENTS

”

FRIULINOX ALI GROUPS.R.L. A SOCIO UNICO

Via Treviso,4 - 33083 Taiedo di Chions (PN) -Italy

Servi

9.2.3.

The display board is on but it is not possible to access the functions by pressing the keys

see
par.

8.1

With the display on, if the functions cannot be accessed by pressing the keys, put the

equipment in stand-by, disconnect voltage and access the electronic card

Make sure there is no oxide on the flat cable terminals. If necessary, remove the oxide

Give power again and make sure there are 230V +/-10% between

the “L” and “N” “faston” type terminals



see wiring diagram

Check that the power supply voltage at transformer output (12VDC) is stable

If it is still not possible to access the functions, press the keys



replace the electronic board

Summary of Contents for Cube Series


























































































Search results

Summary of Contents for Cube Series

Reviews:

Related manuals for Cube Series

Brands by name

Popular brands

Friulinox Cube Series, Service Manual

Search results

Summary of Contents for Cube Series

Reviews:

Related manuals for Cube Series

Brands by name

Popular brands