Friulinox Cube Series Service Manual Download

Page: 5 / 89

“go to

TABLE

OF CONTENTS

”

FRIULINOX ALI GROUPS.R.L.

A SOCIO UNICO

Via Treviso,4 - 33083 Taiedo di Chions (PN) -Italy

Servi

GENERAL WARNINGS

ATTENTION! Live equipment. Always disconnect voltage when performing
maintenance and cleaning on the equipment.

ATTENTION! Potentially dangerous situation that could harm people or
damage objects near-by.

SUGGESTION
Ideas or advice for maintenance or intervention.

ATTENTION:

THE USE OF NON-ORIGINAL SPARE PARTS PURCHASED FROM THIRD PARTIES NOT

AUTHORISED BY FRIULINOX ALI GROUP SRL, AND THEIR MODIFICATION IN A

CONFIGURATION DIFFERENT FROM THE ORIGINAL, CANCEL THE EQUIPMENT AND

COMPONENT WARRANTY. FRIULINOX ALI GROUP SRL AND ITS AUTHORISED CENTRES

WILL NOT BE HELD LIABLE FOR COMPLAINTS, DAMAGES AND COSTS CAUSED DIRECTLY

OR INDIRECTLY BY CHANGES NOT APPROVED AND VALIDATED BY THE SAME.

DO NOT CLEAN THE EQUIPMENT WITH PRESSURE WATER.

DO NOT WORK ON THE EQUIPMENT WITHOUT HAVING READ THIS MANUAL.

DO NOT WORK ON THE EQUIPMENT IF THE ACCESS PANELS ARE NOT CORRECTLY

POSITIONED AND SECURED.

DO NOT WORK ON THE EQUIPMENT IF NOT CORRECTLY INSTALLED AND SERVICED.

PAY ATTENTION WHEN MOVING THE EQUIPMENT. IT CAN WEIGH FROM 50 KG TO 257

KG. USE THE SPECIFIC LIFTING SYSTEMS

CONNECTION TO THE POWER MAINS AND THE CONNECTION SYSTEMS MUST MEET THE

REGULATIONS IN FORCE IN THE COUNTRY OF INSTALLATION OF THE EQUIPMENT AND

MUST BE CARRIED OUT BY QUALIFIED PERSONNEL AND AUTHORISED BY THE

MANUFACTURER.

Summary of Contents for Cube Series


























































































Search results

Summary of Contents for Cube Series

Reviews:

Related manuals for Cube Series

Brands by name

Popular brands

Friulinox Cube Series, Service Manual

Search results

Summary of Contents for Cube Series

Reviews:

Related manuals for Cube Series

Brands by name

Popular brands