Friulinox Cube Series Service Manual Download

Page: 36 / 89

“go to

TABLE OF CONTENTS

”

FRIULINOX ALI GROUPS.R.L. A SOCIO UNICO

Via Treviso,4 - 33083 Taiedo di Chions (PN) -Italy

Servi

8.5.

Condenser filter panel removal and cleaning

Loosen the central screw closing the front panel using a
screwdriver.

Lift the front panel, being careful to secure it to the

rear body.

Remove the springs that fix the filter panel with a
clamp.

Remove the filter panel from the seat.

Use a solution of water and neutral soap to clean it.

Reposition the filter panel in the seat.

Secure again the filter panel to the condenser with the
springs.

Do the same with the front panel, tear-strip

attached to the control panel.

Close the front panel again, paying attention to

the door microswitch.

Summary of Contents for Cube Series


























































































Search results

Summary of Contents for Cube Series

Reviews:

Related manuals for Cube Series

Brands by name

Popular brands

Friulinox Cube Series, Service Manual

Search results

Summary of Contents for Cube Series

Reviews:

Related manuals for Cube Series

Brands by name

Popular brands