Friulinox Cube Series Service Manual Download

Page: 26 / 89

“go to

TABLE OF CONTENTS

”

FRIULINOX ALI GROUPS.R.L. A SOCIO UNICO

Via Treviso,4 - 33083 Taiedo di Chions (PN) -Italy

Servi

7.2.4.

Reset Data Memories (HACCP)

7.2.5.

Reset Factory Values

7.2.6.

HACCP

The following alarms are visible in the SERVICE menu, under HACCP:

Minimum Temp

minimum temperature alarm: the minimum temperature in disagreement with the setpoint has been reached.

Maximum Temp

maximum temperature alarm: the maximum temperature in disagreement with the setpoint has been reached.

Door Open

door microswitch alarm: indicates the maximum temperature reached with prolonged door opening.

Power Failure

power supply stop alarm: indicates the cell temperature upon power supply reset.

The alarm description shows:
Date and time in which the alarm occurred*.
Alarm duration in hours and minutes.
Critical temperature reached during the alarm.

for the board with code BN1681232, these values follow the settings present in the Real Time Clock (rtc) menu

Summary of Contents for Cube Series


























































































Search results

Summary of Contents for Cube Series

Reviews:

Related manuals for Cube Series

Brands by name

Popular brands

Friulinox Cube Series, Service Manual

Search results

Summary of Contents for Cube Series

Reviews:

Related manuals for Cube Series

Brands by name

Popular brands