Friulinox Cube Series Service Manual Download

Page: 16 / 89

“go to

TABLE OF CONTENTS

”

FRIULINOX ALI GROUPS.R.L. A SOCIO UNICO

Via Treviso,4 - 33083 Taiedo di Chions (PN) -Italy

Servi

INSTALLATION CHECK LIST

Refrigerated cabinets installation checklist

rev0 of 17/11/2017

Customer name

Installation date

Address

Installer technician

City

Installer company

Country

Model

Tel. no.

Serial number

E-mail address

Power supply voltage

Reference contact

Checks

Notes

Check the package status and integrity



Check for aesthetic defects



Remove the protective film from all surfaces



Cabinet installed on wheels?

YES □

NO □

Condensing unit on the machine?

YES □

NO □

Check that the evaporator cover is correctly
fastened with belt



Indicate the available space around the storage cabinet:

left side -

minimum 50 (mm)

…………..

right side -

minimum 50 (mm)

…………..

front (mm)

…………..

back -

minimum 50 (mm)

…………..

above -

minimum 500 (mm)

…………..

Indicate the equipment around the cabinet (oven/refrigerator/blast chiller/refrigerated
counters/worktable/dishwasher/wall/free/other)

left side

…………………………………………………………………………………………………………………….

right side

…………………………………………………………………………………………………………………….

front

…………………………………………………………………………………………………………………….

back

…………………………………………………………………………………………………………………….

above

…………………………………………………………………………………………………………………….

Level equipment (recommended inclination of 2%
to the front)



Electrical connection

Make sure that the power socket is equipped
with a 30mA thermal breaker



Connect the single-phase models to the power
socket via Shuko plug (already installed)



Only for water-condensation units (WL)

Check the seal of the hydraulic connections



Indicate the condenser inlet water pressure

- max

5 (bar)

…………..

Indicate the condenser inlet water temperature -

max 30(°C)

…………..

Calibrate the pressure valve at 13 - 15 bar (WL
version only)



Summary of Contents for Cube Series


























































































Search results

Summary of Contents for Cube Series

Reviews:

Related manuals for Cube Series

Brands by name

Popular brands

Friulinox Cube Series, Service Manual

Search results

Summary of Contents for Cube Series

Reviews:

Related manuals for Cube Series

Brands by name

Popular brands