Fritz! Box 6490 cable Installation And Operation Manual Download Page 20

Page: 20 / 173

FRITZ!Box 6490 Cable

Connecting a Network Hub or Switch

5.2

Connecting a Network Hub or Switch

You can connect a network hub or network switch to the
FRITZ!Box.

Insert the network cable included in the package into
the uplink port of the network hub or network switch.

You can also use any other network cable. For more in-
formation, see

page 160

Insert the free end of the cable into a LAN socket on the
FRITZ!Box.

The FRITZ!Box and the network hub are now connected with
each other.

FON 1

FON 2

LAN

LAN 1

LAN

LAN 2

LAN

LAN 3

LAN 4

Power

FON S

FON S0

Info

WLAN

DECT

Fon

Power/Cable

CABLE

Summary of Contents for Box 6490 cable














































































































































































Search results

Summary of Contents for Box 6490 cable

Reviews:

Related manuals for Box 6490 cable

Brands by name

Popular brands

Fritz! Box 6490 cable, Installation And Operation Manual

Search results

Summary of Contents for Box 6490 cable

Reviews:

Related manuals for Box 6490 cable

Brands by name

Popular brands