Fritz! Box 6490 cable Installation And Operation Manual Download Page 158

Page: 158 / 173

FRITZ!Box 6490 Cable

158

Router Functions

•

Wireless access point with support for wireless LAN ra-
dio networks

–

IEEE 802.11a – 54 Mbit/s

–

IEEE 802.11b – 11 Mbit/s

–

IEEE 802.11g – 54 Mbit/s

–

IEEE 802.11n – 450 Mbit/s

–

IEEE 802.11ac – 1300 Mbit/s

26.3

Router Functions

•

Router

•

DHCP server

•

Firewall with IP masquerading/NAT

•

IPv4 and IPv6

•

Parental controls and filter lists

•

Port Forwarding

•

Dynamic DNS

•

VPN

26.4

User Interface and Display

•

Configuration and status messages via a web browser on
a connected computer

•

Five LEDs indicate the condition of the device

26.5

Tones

•

Busy signal: 500 ms tone, 500 ms pause, +/– 20 ms

•

Ring tone: 1 s tone, 4 s pause +/– 100 ms

Summary of Contents for Box 6490 cable














































































































































































Search results

Summary of Contents for Box 6490 cable

Reviews:

Related manuals for Box 6490 cable

Brands by name

Popular brands

Fritz! Box 6490 cable, Installation And Operation Manual

Search results

Summary of Contents for Box 6490 cable

Reviews:

Related manuals for Box 6490 cable

Brands by name

Popular brands