Fritz! Box 6490 cable Installation And Operation Manual Download Page 157

Page: 157 / 173

Technical Specifications

FRITZ!Box 6490 Cable

157

Technical Specifications

Facts worth knowing: Here you will find comprehensive technical data
on your FRITZ!Box 6490 Cable.

26.1

Network Access Interface

The FRITZ!Box 6490 Cable fulfills the interface specification
for public network in accordance with the following standards
and directives:

•

ETSI TS 102 639 (DOCSIS or EuroDOCSIS 3.0 cable
broadband access for Internet and telephony)

•

IETF RFC 3261 (Session Initiation Protocol for Voice over IP)

•

Broadband Forum TR-069 (CPE WAN Management Protocol)

26.2

Ports and Interfaces

•

Cable port

cable modem compliant with DOCSIS 3.0 or
EuroDOCSIS 3.0, downward compatible with
EuroDOCSIS 1.0, 1.1 and 2.0 supports up to 24 chan-
nels in the receive direction and up to 8 channels in the
send direction

•

Two a/b ports with RJ11 and TAE sockets for connecting
two analog terminal devices

•

One ISDN S

NT port

bus with support for ISDN terminal devices; the CIP

services voice, telephony, audio 3.1 and fax G2/G3 are
supported

•

DECT Base Station

•

Four LAN ports via RJ45 sockets (standard Ethernet,
10/100/1000 Base-T)

•

Two USB host controllers (USB version 2.0)

Summary of Contents for Box 6490 cable














































































































































































Search results

Summary of Contents for Box 6490 cable

Reviews:

Related manuals for Box 6490 cable

Brands by name

Popular brands

Fritz! Box 6490 cable, Installation And Operation Manual

Search results

Summary of Contents for Box 6490 cable

Reviews:

Related manuals for Box 6490 cable

Brands by name

Popular brands