Fritz! Box 6490 cable Installation And Operation Manual Download Page 131 | Manualshive

Page: 131 / 173

background image

Sharing a USB Printer

FRITZ!Box 6490 Cable

131

•

the USB printer uses bidirectional data exchange. In oth-
er words: Not only does the computer send data to the
printer, the printer also sends status messages to the
computer. This communication in both directions is typi-
cal of the “Windows printers” or “GDI printers” that work
only with special Windows device drivers.

For information about how to configure a USB printer with the
USB remote connection, continue reading from the section

Configuring a USB Printer with FRITZ!Box USB Remote
Connection

.

Configuring a USB Printer as a Network Printer

Connect the USB printer to the USB port of the FRITZ!Box.

Preparing Configuration

1.

Open the FRITZ!Box user interface; see

.

2.

Enable the advanced view.

3.

Select the “Home Network / USB Devices” menu.

4.

Select the “USB Remote Connection” tab.

5.

Disable the option “printers (including all-in-one print-
ers)”.

6.

Save your settings by clicking “Apply”.

7.

Connect the USB printer to the FRITZ!Box.

This concludes the preparations. Continue reading in the sec-
tion for your operating system.

Setting Up a USB Printer in Windows 8, Windows 7 and Vista

1.

Click “Start / Control Panel” and select the printer cate-
gory of your operating system:

–

“Hardware and Sound / Devices and Printers”
(Windows 8 , Windows 7)

–

“Printers” (Windows Vista)

2.

Click the printer icon with the right mouse button and se-
lect “Properties” or “Printer properties”.

«
...
129
130
131
132
133
...
»

Summary of Contents for Box 6490 cable














































































































































































Reviews:

No comments

Related manuals for Box 6490 cable

Brand: D-Link Pages: 15

DSN-4100 Series

Brand: D-Link Pages: 2

Brand: D-Link Pages: 2

3CR860-95 - OfficeConnect Secure Router

Brand: 3Com Pages: 2

Brand: 3Com Pages: 26

Storage Networking (Unified Fabric Pilot)

Brand: Qlogic Pages: 76

ExpressBox2 EB2

Brand: Magma Pages: 74

Brand: Tripp Lite Pages: 34

Ethernet MCA 10/100 Adapter

Brand: Olicom Pages: 88

Brand: 2N Telekomunikace Pages: 67

Brand: Extron electronics Pages: 19

Brand: NETGEAR Pages: 20

GlobeSurfer X-1

Brand: Option Audio Pages: 30

Brand: MiLAN Pages: 155

ELITE LCD UPGRADE KIT

Brand: Corsair Pages: 11

Brand: Eaton Pages: 32

Brand: AMCI Pages: 55

Brand: Huawei Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands