manualshive.com logo in svg

Fritsch PULVERISETTE 1 classic line, Operating Instructions Manual, Page: 33 / 56

Share
Download
Fritsch PULVERISETTE 1 classic line Operating Instructions Manual Download Page 33

7 

Accessories

7.1  Conversion for use with the dust exhaust system

n

43.9050.00 Dust exhaust system

n

43.9051.00 Polyester filter set (pack of 2)

n

43.9052.00 Plastic bag (pack of 5)

The Laboratory - Jaw Crusher is delivered without the dust exhaust

system. In order to use the dust exhaust system, the back cover has to be

replaced by a special cover for dust exhaust.
It is located in the grinding stock container of the device together with

the required hexagon socket screw key when the device is delivered.

DANGER!
Mains voltage!
The device has to be disconnected from the mains

before beginning assembly work (by pulling the mains

plug out of the socket).
Assembly work may be only be carried out by a trained

electrician.

1.

Unscrew the lower hexagon screws (b) by turning them once.

Remove the two upper screws completely.

2.

Pull the cover upward to remove it.

 

Accessories

 

 

- 33 -

 

Summary of Contents for PULVERISETTE 1 classic line

























































Reviews:

No comments