manualshive.com logo in svg

Fristam Pumps FP, Original Instructions, Assembly Instructions, Page: 28 / 40

Share
Download
Fristam Pumps FP Original Instructions, Assembly Instructions Download Page 28

/ / FP PUMP SERIES / / /

28

10 Appendix 1

10.1 Specifications

10.1.1 Tightening Torques for Screws and Nuts

Material: Steel, Strength Class: 8.8

Material: Stainless Steel, Strength Class: 70

Material: Stainless Steel, Strength Class: 80

10.1.2 Noise Emissions

10.2 Maintenance Intervals

1

1

For information on motor maintenance intervals, please see the motor operator's manual.

Thread

M6

M8

M10

M12

M16

M20

Tightening 
Torque [Nm]

11

27

54

93

230

464

Thread

M6

M8

M10

M12

M16

M20

Tightening 
Torque [Nm]

7.4

17.5

36

62

150

303

Thread

M6

M8

M10

M12

M16

M20

Tightening 
Torque [Nm]

1o

24

49

80

203

393

Pump Size

Noise Level

dBA

711/712

75

721/722

71

741/742

79

751/752

78

3401/3402

71

3521/3522

74

3531/3532

79

3541/3542

78

3451/3452

81

3551/3552

81

1151/1152

89

1231/1232

79

1241/1242

89

1251/1252

92

Table 12  Noise emissions

The specified values apply to operation of the pump at the best 
efficiency point (see 

"Pump Characteristic Curve"

). The noise level 

can differ greatly at other working points.

Model

Interval

Maintenance Task

Chapter

All with "Sealing and Quench-
ing Liquid" option

Once a day

Check the sealing or quenching liq-
uid.

See 

Chapter 9.3, "Inspection of Sealing and Quenching Liquid 

(Optional)," page 15

.

L 2, L 3/L3V, L 4V

Once a day

Check the oil level.

KF1,KF 2, KF 3

5,000 h

Lubricate the shaft bearing.

See 

Chapter 9.5.4, "Model KF," page 16

.

L 2, L 3/L3V, L 4V

5,000 h

Change the oil.

See 

Chapter 9.5.2, "Models L 2, L 3/L3V and L 4V," page 15

.

L1 

5,000 h

Lubricate the shaft bearing.

See 

Chapter 9.5.3, "Model L1," page 16

.

All

When necessary

Replace the shaft seal.

See 

Chapter 9.7, "Shaft Seal Replacement," page 18

.

All

When necessary

Replace the motor.

See 

Chapter 9.6, "Motor Replacement," page 17

.

FPE/FPV

When necessary

Replace the shaft.

See 

Chapter 9.11, "Models FPE and FP…V: Mounting and Align-

ment of the Pump Shaft," page 27

.

All

According to 
manufacturer's 
specifications

Lubricate the motor bearings.

See 

Chapter 9.4, "Lubrication of Motor Bearings," page 15

.

Table 13  Maintenance intervals

Summary of Contents for FP









































Reviews:

No comments