manualshive.com logo in svg

Frigidaire Affinity 6000 Series, Service Manual, Page: 62 / 74

Share
Download
Frigidaire Affinity 6000 Series Service Manual Download Page 62

  Section 4 Component Teardown 

4-20

Drain Hose Coupler Removal

1.   Disconnect the washer from the electrical supply
 

and remove the top panel.

2.   Disconnect the (2) drain hoses and siphon break
 hose.
3.   Remove screw holding coupler to the rear panel and 

pull coupler out the back.  (See Figure 4-83)

Rear Access Panel Removal

1.   Disconnect the washer from the electrical supply.
2.   Remove the (6) screws holding the rear access
 

panel to the washer’s rear panel and lift the access

 

panel off.  (See Figure 4-84)

Drive Belt Removal

The drive belt (6 rib flat Poly-V) is used to transmit 
power from the motor pulley to the tub.  The belt is 
constructed of a material that stretches, which makes 
belt tension adjustments unnecessary.

Removing or replace the drive belt:
1.   Disconnect the washer from the electrical supply 

and remove the rear access panel.

2.   Remove the belt by turning tub drive pulley and 
 

rolling belt off pulley.  The belt is elastic and is 

designed to “give” enough to remove and install in 
this manner.  (See Figure 4-85)

Large Pulley Removal

To remove the large pulley:
1.   Disconnect the washer from the electrical supply.

 
2.   Remove the rear access panel and drive belt.
3.   Using a #6 mm allen wrench remove bolt in the 

center of pulley by holding the pulley and turning 
the bolt counter clockwise.  (See Figure 4-86)

4.   Work the pulley back and forth to remove it from 

the shaft.

Figure 4-83.

Figure 4-85.

Figure 4-86.

Screw

Figure 4-84.

Screws

Belt

Summary of Contents for Affinity 6000 Series











































































Reviews:

No comments