background image

2

WARNING

CAUTION

Please entrust the distributor or professionals to install the unit.

Strictly follow this manual.

Reinstallation must be performed by professionals.

Do not disassemble your air conditioner at will.

Do not install the unit in a place vulnerable to leakage of flammable gases.

The wiring should adapt to the wire controller current.

The specified cables shall be applied in the wiring. No external force may 

be applied to the terminal.

Do not place the wired remote controller near the lamps, to avoid the remote 

signal of the controller to be disturbed. (refer to the right figure)

Installation by other persons may lead to imperfect installation, electric shock or fire.

Imporper installation may lead to electric shock or fire.

improper installation may lead to electric shock or fire.

A random disassembly may cause abnormal operation or heating, which may result in fire.

Once flammable gases are leaked and left around the wire controller, fire may occure.

Otherwise, electric leakage or heating may occur and result in fire.

Otherwise, wire cut and heating may occur and result in fire. 

Summary of Contents for GW-KNX(A)
















Reviews: