background image

                    Shenzhen Friendcom Technology Development Co., Ltd. 

 

15

 

Power Save Time 

When Power save is enable, sleep time can be programmed from 20 to 500 ms in 20ms increment with 1~25 
optional values. That means 1 equals to 20 ms, 2 equals to 40ms ....... 25 equal to 500ms 
Standby time can also be programmed from 40 to 600 ms in 40ms increment with 
1~15 optional values. That means 1 equals to 40ms, 2 equals to 80, ..... 15 equals to 600ms. 
 

4.2.3.3.5 Carrier Detect Busy Signal 

 

This feature is to set active level of BUSY Pin, high or low. The status is transferred to user for the connection 
with external devices. 
 

4.2.3.4 Third Column Features 

 

4.2.4.4.1 Audio-out 

Output wave for Audio-out can be selected as square wave or sin wave. 
 

4.2.4.4.2. Side Tone 

When enabled, user can hear his own voice while transmitting voice. The sidetone volume is fixed at level 2 
de-emphasis volume.

 

 

4.2.4.4.3 RSSI 

To detect the air signal strength over the air

 

Unit

dBuv

 

 

4.2.4.4.4 Channel Scan 

Scan modes are set up in “Option” and shown as below 
0 ---------normal scan with carry only 
1 ---------normal scan, carry with tone 
2 ---------priority scan, carry only 

Summary of Contents for FC-302 U2





















Reviews: