D412
Fig 3
Fig 5
Fig 6
Fig 7
Fig 2
6. Programming of bell push transmitter(s)
The first time the chime is powered up, the sounds available are
demonstrated. First make sure that the door push and the chime
are separated by at least 1m (3 ft). Press the door push until the
chime responds with a tune.You can leave this tune or change it
to a desired tune by using button A (Fig 6)(see Sound Selection
for tune list). To program for a second push, press the push until
the chime sounds, then use button B to change the tune if
required. Programming is now completed.
If more than five minutes has elapsed, you will have to reset the
chime programming by pressing and holding buttons A and B
until the chime sounds, this takes approximately 5 seconds.
The chime can then be programmed to 1or 2 door pushes.
All EVO and Décor chimes and bell pushes use this self-learning
feature to ensure no interaction from other neighbouring systems.
7. Sound Selection
A = Main push sound selection
B = Second push sound selection
Chime tune options are as follows
8. Flashing Light and sound controls
The settings are:
0. Sound only
1. Sound with flashing light
2. Flashing light only
Flashing Light and sound control
To turn the door chime sound off or to stop the flashing LED light
when the bell push is pressed, turn knob C
Note:
when the chime is being programmed this control will
not function for 5 minutes.
Trouble Shooting
Chime not Sounding
Batteries may not be inserted correctly
Check all batteries have been inserted correctly
Chime may be positioned out of range of the bell push
Move your chime closer to the bell push
A metallic object may be blocking the signal from bell push position
Experiment with the location of the chime to see if you can
move it in a more suitable place
The battery in the bell push may need replacing
Press the bell push. If the confidence light (B) flashes 5 times
after being pushed, replace the battery.
Note:
In cold conditions, poor location or environment,
operating at maximum range it is advisable to replace the
battery more frequently before the indicator light flashes
(i.e every 12 - 18 months) to maintain optimum performance
Your bell push and chime haven't been programmed
Do the automatic programming of your chime and bell push
The Selection knob may have been set incorrectly
Reset position of knob C as described in section 8 above
LED flashing light does not flash
The selection knob is not set correctly,
reset position of knob C
as described in section 8 above
-
+
+
-
+
-
Chime Sound Variety:
1. Big Ben 2 Note (Default Tune for 1st Push)
2. Mini Bell 4 Note w/ Echo (Default Tune for 2nd Push)
3. Clarinet
4. Altosax
A
C
B
C
*
The stated transmission range of this product is measured in open field conditions.
Walls ceilings, and metal structures will reduce the maximum range.
Fig 1
0
2
1
Declaration
Novar ED&S hereby declares that this wirefree chime kit is in compliance with
the essential requirements and other relevant provisions of the Radio and
Telecommunications Terminal Equipment ( R & TTE ) directive, 1999/5/EC
LED light
Friedland guarantees this product for 3 years from date of purchase.
Proof of purchase required, this does not affect your statutory rights.
If you require further information about our products, call the Friedland helpline
on 01268 563066.
Friedland a Novar business, Novar ED&S, The Arnold Centre, Paycocke Road
Basildon, Essex, SS14 3EA, England
www.friedland.co.uk
Evo Wirefree 200M* Chime with
Flashing Light
Instructions
– Please retain these instructions for future reference
Pack contents:
Portable Door Chime with Flashing light
Bell push & CR2032 Lithium coin cell battery
Adhesive pad, 2 x screws (ø3 x 20mm) 2 x wall plugs (ø5 x25 mm)
for mounting the bell push
You will require
3 X LR6 (AA) Alkaline batteries for the Portable Door Chime.
Only long-life Alkaline batteries must be used.
A small crosshead and flathead screwdriver, a ø5 masonry drill
Installation
Please note:
The stated range of this product is measured in
open field conditions. Walls, ceilings and the positioning the
bell push or door chime on or near metal structures or
reinforced PVC doors or doorframes will reduce the
transmission range.
1. Open the bell push
To open the front cover carefully
insert a flat bladed screw driver,
into the slot and twist gently (A).
When refitting the front cover to
ensure the weather proofing is
maintained, always mount the
bell push in the upright position
and replace the cover securely. Fig 1
2. To fit or replace the battery
Open the front cover and insert
the CR 2032 Lithium coin cell
battery into the base as shown
in Fig. 2. Any debris created
during installation must be
removed from the base before
fitting battery, to ensure good contact.
3. Mount the bell push
Ensure the wall surface is clean
and dry. Mount using either the
double sided sticky pad on a
smooth surface, or the screws
and wall plugs provided, See Fig 3.
Do not mount the push on or near
(< 30cm) large metal objects, as it
will block signals from the push.
4. Test the bell push
When the bell push button is pressed,
the confidence light (B) in Fig 4, will
illuminate to reassure the caller that
the bell push is working.
The light will flash 5 times when
the battery needs replacing.
5. Fitting or replacing the batteries in the door-chime
Remove battery compartment
cover and insert three
LR6 (AA) alkaline batteries
as shown in Fig 5.
Refit the battery
compartment cover.
+
Fig 4
