background image

SIRe Advanced Fan Heater  Water

40

GB

Table - Error codes

Error code

Cause 

Action

E1
 

SIReB1(X) has no contact 
with SIReA1X.
 

Check connection between the 
boards. Replace any modular 
cables.
 

Communication

E2 
 

ID Error

Two or more SIReB1(X) have 
the same ID-number.
 

Interrupt the current and select 
different ID numbers for all 
SIReB1(X) in the system.
 

E3
 

ID Error

One or more SIReB1(X) do not 
have programs.
 

Contact Frico for support.
 

E4
 

Room sensor 
error

Fault on or missing external room 
sensor SIReRTX connected to 
SIReB1(X).
 

Always disconnect the power 
when connecting or disconnecting 
sensors. Check connection of the 
sensor.
 

E6

Sensor alarm Return 
water temp.

Fault on or missing return 
water temp. sensor SIReWTA 
connected to SIReB1(X).
 

Always disconnect the power when 
connecting or disconnecting sensors. 
Check connection of the sensor. If 
the sensor is not used, it must not be 
activated (see the Settings heating 
section)
 

E8
 

Internal sensor faults Fault on or missing internal 

sensor in the unit.
 

Check connection of the sensor. If 
there is no sensor, contact Frico 
for support.
 

E10
 

ID Error

Two or more SIReB1(X) in 
the system have different 
programs.
 

Contact Frico for support.
 

E12
 

Room sensor error

Fault on or missing external 
room sensor SIReRTX 
connected to SIReA1X.
 

Always disconnect the 
power when connecting or 
disconnecting sensors. Check 
connection of the sensor.
 

E14
 

Outdoor sensor fault Fault on or missing outdoor 

temperature sensor SIReOTX 
connected to SIReA1X.
 

Always disconnect the power when 
connecting or disconnecting sensors. 
Check connection of the sensor.
 

E20
 

Communication

Control unit SIReUA1 has no 
contact with SIReA1X.
 

Check the connection. Replace any 
modular cables.
 

E21
 

Room sensor error

Error in the internal room 
sensor in the control unit 
SIReUA1.
 

Check connection between SIReUA1 and 
SIReA1X. Replace any modular cables. If 
the error is not rectified SIReUA1 must 
be replaced.
 

E23
 

Soft ware error

Contact Frico for support.
 

Summary of Contents for sirefa


























Reviews: