Frick QUANTUM HD UNITY Maintenance Manual Download Page 61

Page: 61 / 64

QUANTUM™ HD UNITY SYSTEM CONTROLLER

MAINTENANCE

090.670-M (APR 2020)

Page 61

Part Number

Description

Analog board

640C0062G01

Analog board replacement (use existing board to configure new board)

640C0062G12

Analog board field installation/upgrade kit (use maintenance manual to properly configure

the new board for the application)

Digital boards

640C0024G71

Digital board field installation/upgrade kit (use maintenance manual to properly configure the

new board for the application)

640C0024G01

Digital board replacement (use existing board as a reference to configure new board)

111Q0281061

Output module, 24 VAC to 280 VAC

333Q0000116

Input module, 120 VAC

333Q0000789

Input module, 220 VAC

333Q0001326

Fuse, 5 amp, 250 V

Power supplies

639B0115H01

5 VDC power supply, 25 W

639D0296H01

12 VDC power supply, 72 W

639D0296H02

24 VDC power supply, 72 W (main unity controller)

639B0115H03

24 VDC power supply, 48 W (remote evaporator I/O panel)

Processor boards*

649C1170G01

Q6 processor board

649C1171G11

Q5 to Q6 Quantum HD Unity condenser/vessel upgrade kit

649C1171G21

Q5 to Q6 Quantum HD Unity evaporator upgrade kit

649C1171G31

Q5 to Q6 Quantum HD Unity engine room upgrade kit

Interface boards

639B0116H01

Interface board (used with Q5 processor board only)

Display/Touchscreen

639D0199H01

Display (indoor)

649D6101G01

Touchscreen overlay (FRICK)

HOA modules

643D0072G01

Module #1 (condenser)

643D0072G02

Module #2 (condenser)

SECTION 8

REPLACEMENT PARTS

REPLACEMENT PARTS LIST

Summary of Contents for QUANTUM HD UNITY

































































Search results

Summary of Contents for QUANTUM HD UNITY

Reviews:

Related manuals for QUANTUM HD UNITY

Brands by name

Popular brands

Frick QUANTUM HD UNITY, Maintenance Manual

Search results

Summary of Contents for QUANTUM HD UNITY

Reviews:

Related manuals for QUANTUM HD UNITY

Brands by name

Popular brands