manualshive.com logo in svg

Freescale Semiconductor Symphony DSP56724, Reference Manual

The Freescale Semiconductor Symphony DSP56724 is a cutting-edge product that offers high-performance digital signal processing capabilities. Unlock its full potential with the comprehensive Reference Manual, available for free download from our website. Experience enhanced functionality and optimize your user experience with this invaluable manual.

Share
Download
background image

Signal Descriptions

Symphony DSP56724/DSP56725 Multi-Core Audio Processors, Rev. 0

Freescale Semiconductor

2-29

 

2.2.14

JTAG/OnCE Interface Signals

PG2

Input, Output, or 

Disconnected

MODD1 Input

Port G2

When the PLOCK is configured as GPIO, this signal is individually 
programmable as input, output, or internally disconnected.

MODD1

Input

MODA1, MODB1, MODC1, and MODD1 levels select one of 16 initial chip 
operating modes of DSP Core-1, and are latched into the DSP Core-1’s 
OMR when the RESET signal is deasserted. 
Uses an internal pull-down resistor. 
This signal is only available in the DSP56724 144-pin package. This signal 
is not available in the DSP56725 80-pin package.

Table 2-21. JTAG/OnCE Interface

Signal 

Name

Signal 

Type

State During 

Reset

Description

TCK

Input

Input

Test Clock

TCK is a test clock input signal used to synchronize the JTAG test logic. It uses an 
internal pull-up resistor.

TDI

Input

Input

Test Data Input

TDI is a test data serial input signal used for test instructions and data. TDI is sampled 
on the rising edge of TCK and uses an internal pull-up resistor.

TDO

Output

Tri-Stated

Test Data Output

TDO is a test data serial output signal used for test instructions and data. TDO is 
tri-statable and is actively driven in the shift-IR and shift-DR controller states. TDO 
changes on the falling edge of TCK.

TMS

Input

Input

Test Mode Select

TMS is an input signal used to sequence the test controller’s state machine. TMS is 
sampled on the rising edge of TCK and uses an internal pull-up resistor.

Table 2-20. Dedicated Port G Signals and Mode Pins (Continued)

Signal Name

Type

State During 

Reset

Description

Summary of Contents for Symphony DSP56724





















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Symphony DSP56724

Magiccos FP406 Quick Start Manual preview
FP406
Brand: Magiccos Pages: 2
BenQ InstaShow WDC10R User Manual preview
InstaShow WDC10R
Brand: BenQ Pages: 31
Bravetti KP80B Owner'S Manual preview
KP80B
Brand: Bravetti Pages: 6
Skymsen PA-7S Instruction Manual preview
PA-7S
Brand: Skymsen Pages: 6
CYP WPS-QPL01 Operation Manual preview
WPS-QPL01
Brand: CYP Pages: 24
Navitar 586MCL047 Installation Instructions preview
586MCL047
Brand: Navitar Pages: 1
cecotec CHOPBEAT 1500 Instruction Manual preview
CHOPBEAT 1500
Brand: cecotec Pages: 76
ARENDO 20190806SZ253 User Manual preview
20190806SZ253
Brand: ARENDO Pages: 80
Hamilton Beach Professional B96 Operation Manual - Original Instructions preview
B96
Brand: Hamilton Beach Professional Pages: 8
eta Basto 1079 User Manual preview
Basto 1079
Brand: eta Pages: 44
Team Kalorik TKG MCH 1000 Manual preview
TKG MCH 1000
Brand: Team Kalorik Pages: 36
G. Paniz PA 27 Instruction Manual preview
PA 27
Brand: G. Paniz Pages: 10
Faber FCB 1030 Instruction Manual preview
FCB 1030
Brand: Faber Pages: 8
Barco XDL Installation Manual preview
XDL
Brand: Barco Pages: 88
Califone Wireless PresentationPro PA329 Owner'S Manual preview
Wireless PresentationPro PA329
Brand: Califone Pages: 8
Da-Lite 22516 Installation Instructions Manual preview
22516
Brand: Da-Lite Pages: 12
Conrad-johnson design D/A-1 Owner'S Manual preview
D/A-1
Brand: Conrad-johnson design Pages: 8
Hamilton Beach 72860-CN Quick Start Manual preview
72860-CN
Brand: Hamilton Beach Pages: 2

Brands by name

Popular brands

Load more brands