manualshive.com logo in svg

Freescale Semiconductor Symphony DSP56724, Reference Manual, Page: 328 / 436

Share
Download
Freescale Semiconductor Symphony DSP56724 Reference Manual Download Page 328

Symphony DSP56724/DSP56725 Multi-Core Audio Processors, Rev. 0

20-16

Freescale Semiconductor

 

Chip Configuration Module

Figure 20-12. SPDIFIN1 and ESAI Pin Mux in 80-Pin Packages

In DSP56725 80-pin packages, the PMC[14] bit enables/disables the pin mux of the SPDIFIN1 and 
ESAI_2 SDO2_2/SDI3_2 pins. When the PMC[14] bit is set (1), the shared ESAI_2 SDO2_2/SDI3_2 pin 
is used as the SPDIFIN1 input and the ESAI_2 output on this pin is disabled. When the PMC[14] bit is 
cleared (0), this pin is controlled by ESAI_2. 

Figure 20-13. SPDIFOUT1 and ESAI_2 Pin Mux In 80-Pin Packages

In DSP56725 80-pin packages, the PMC[15] bit enables/disables the pin mux of the SPDIFOUT1 and 
ESAI_2 SD03_2/SDI2_2 pins. When the PMC[15] bit is set (1), this shared ESAI_2 pin is used as the 
SPDIFOUT1 output and the ESAI_2 input on this pin is disabled. When the PMC[15] bit is cleared, this 
pin is controlled by ESAI_2. 

20.3.3

Soft Reset

The chip configuration module contains a soft reset control register used for triggering soft reset to 
different shared peripherals. The bit definitions of the PSRC register describes the functionality of each bit 
that will trigger a soft reset to its corresponding peripheral. Writing “1” to a specific bit of the PSRC 
register will cause a soft reset of the corresponding peripheral. The PSRC register bit will be cleared 

SPDIF

SPDIFIN1

ESAI_2

SPDIF pin mux

Chip ESAI_2 SDO2_2/SDI3_2 pin

Control by PMC[14]

sdo2_2/sdi3_2 signal

esai pin
switch

SPDIFIN1 not available on 
DSP56725 80-pin packages.

SPDIFOUT1

ESAI_2

SPDIF pin mux

ESAI pin
switch

Chip ESAI_2 SDO3/SDI2 pin

Controlled by PMC[15]

sdo3_2/sdi2_2 signal

SPDIF

SPDIFOUT1 not available on 
DSP56725 80-pin packages.

Summary of Contents for Symphony DSP56724





















































































































































































































































































































































































































































Reviews:

No comments