manualshive.com logo in svg

Freescale Semiconductor PXR4030, Reference Manual

Share
Download
Freescale Semiconductor PXR4030 Reference Manual Download Page 1354

Nexus Development Interface (NDI)

31-38

Freescale Semiconductor

PXR40 Microcontroller Reference Manual, Rev. 1

After the ACCESS_AUX_TAP_ONCE instruction has been loaded, the JTAG/OnCE port allows 
tool/target communications with all Nexus3 registers according to the register map in 

Table 31-23

.

Reading/writing of a NZ7C3 register then requires two (2) passes through the data-scan (DR) path of the 
JTAG state machine (see 31.14.10).

1. The first pass through the DR selects the NZ7C3 register to be accessed by providing an index (see 

Table 31-23

), and the direction (read/write). This is achieved by loading an 8-bit value into the 

JTAG data register (DR). This register has the following format:

2. The second pass through the DR then shifts the data in or out of the JTAG port, lsb first.

a) During a read access, data is latched from the selected Nexus register when the JTAG state 

machine passes through the capture-DR state.

b) During a write access, data is latched into the selected Nexus register when the JTAG state 

machine passes through the update-DR state.

31.12 Ownership Trace

This section details the ownership trace features of the NZ7C3 module.

Ownership trace provides a macroscopic view, such as task flow reconstruction, when debugging software 
written in a high level (or object-oriented) language. It offers the highest level of abstraction for tracking 
operating system software execution. This is especially useful when the developer is not interested in 
debugging at lower levels. 

31.12.1 Ownership Trace Messaging (OTM)

Ownership trace information is messaged via the auxiliary port using an ownership trace message (OTM). 
The e200z7 processor contains a Power Architecture Book E defined process ID register within the CPU.

The process ID register is updated by the operating system software to provide task/process ID 
information. The contents of this register are replicated on the pins of the processor and connected to 
Nexus. The process ID register value can be accessed using the 

mfspr

/

mtspr

 instructions. Please see the 

e200z7 PowerPC

TM

 

Core Reference Manual

 for more details on the process ID register.

The only condition that causes an ownership trace message occurs when the OTR register is updated or 
process ID register by the e200z7 processor, the data is latched within Nexus, and is messaged out via the 
auxiliary port, allowing development tools to trace ownership flow. 

Nexus Register Index:

Selected from values in 

Table 31-23

Read/Write (R/W):

0 Read
1 Write

Nexus register index

(7-bits)

(1-bit)

R/W

RESET Value: 0x00

Summary of Contents for PXR4030



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands