manualshive.com logo in svg

Freescale Semiconductor MSC8144E, Reference Manual

The Freescale Semiconductor MSC8144E Reference Manual is a comprehensive guide for users of this high-performance semiconductor chip. This essential manual is available for free download on our website, providing detailed instructions and insights into utilizing the product's advanced features and capabilities. Don't miss the opportunity to enhance your experience with MSC8144E, download your manual now at manualshive.com.

Share
Download
background image

MSC8144E Reference Manual, Rev. 3

18-8

 Freescale 

Semiconductor

QUICC Engine™ Subsystem

18.2.7

IRAM

The QUICC Engine subsystem includes 48 KB of IRAM that can be used to store processing 
code for the RISC processors. The IRAM can be split into two 24-KB areas assigned individually 
to each of the two RISC processors, or it can be shared by both processors as one contiguous 
48-KB memory space. Access is through the IRAM address register (IADDR) using the IRAM 
data register (IDR). See the QUICC Engine™ Block Reference Manual with Protocol 
Interworking (QEIWRM) for details.

18.3

Serial DMA Controller

The QUICC Engine subsystem has one physical serial DMA (SDMA) channel that interfaces 
with the internal MBus. The QUICC Engine subsystem implements two dedicated virtual SDMA 
channels for each peripheral, one for the receiver and one for the transmitter. Additional virtual 
channels are available for general purpose accesses.

18.3.1

Data Paths

Figure 18-4 is a simplified block diagram that shows the data paths in the MSC8144E. The 
MSC8144E may be implemented with one DDR bus (32 or 64 bit data). 

The CLASS is responsible for distribution of MBus transactions to the various possible targets 
(for example, RapidIO or DDR memory controller) based on the transaction address. See 
Chapter 4, Chip-Level Arbitration and Switching System (CLASS) for details. 

Figure 18-4.  MSC8144E Data Paths

 

QBus

SC3400

SDMA

Multi-User

RAM

UCC3

UCC1

Complex

RISC

QUICC Engine (QUICC Engine Subsystem)

External

DDR

External System

(32 or 64 bit data)

 DDR Bus 

DDR

MEMC

CLASS

RapidIO

Controller

SerDes Interface

DSP

Cores

M3

Memory

PCI

Controller

PCI Bus

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Harman Kardon CITATION 7.0 Owner'S Manual preview
CITATION 7.0
Brand: Harman Kardon Pages: 66
PaloAlto Networks PA-5400 Series Quick Start Manual preview
PA-5400 Series
Brand: PaloAlto Networks Pages: 2
Q-See QC814 Specifications preview
QC814
Brand: Q-See Pages: 2
Dialogic DM/IP601-CPCI-100BT Quick Install Card preview
DM/IP601-CPCI-100BT
Brand: Dialogic Pages: 2
iCEBOX Z86K15 Manual preview
Z86K15
Brand: iCEBOX Pages: 57
Cisco MERAKI MX450 Installation Manual preview
MX450
Brand: Cisco MERAKI Pages: 4
XJTAG XJLink2-CFM User Manual preview
XJLink2-CFM
Brand: XJTAG Pages: 9
Xilinx Zynq-7000 Manual preview
Zynq-7000
Brand: Xilinx Pages: 8
G&D DVI-Vision-IP-Fiber Installation And Operation Manual preview
DVI-Vision-IP-Fiber
Brand: G&D Pages: 240
Digital Voice Systems VC-20-MR2 User Manual preview
VC-20-MR2
Brand: Digital Voice Systems Pages: 32
LST ZEB2-1 Specifications preview
ZEB2-1
Brand: LST Pages: 1
UMAX Technologies SuperMac E100 User Manual preview
SuperMac E100
Brand: UMAX Technologies Pages: 27
Microchip Technology PD-9501-10GCO/AC User'S Installation Manual preview
PD-9501-10GCO/AC
Brand: Microchip Technology Pages: 41
Renesas H8SX1664 User Manual preview
H8SX1664
Brand: Renesas Pages: 21
Aerotech QNP3 Series Hardware Manual preview
QNP3 Series
Brand: Aerotech Pages: 62
Lanpro LP-F22 Series Assembling Instructions preview
LP-F22 Series
Brand: Lanpro Pages: 3
Lefroy Brooks M1-5100 Installation, Operating, & Maintenance Instructions preview
M1-5100
Brand: Lefroy Brooks Pages: 10
SIIG ExpressCard 11-in-1 Reader/Writer Quick Installation Manual preview
ExpressCard 11-in-1 Reader/Writer
Brand: SIIG Pages: 8

Brands by name

Popular brands

Load more brands